This article needs additional citations for verification. (April 2019)
In machining the word "bevel" is not used to refer to a chamfer. Machinists use chamfers to "ease" otherwise sharp edges, both for safety and to prevent damage to the edges.
A "chamfer" may sometimes be regarded as a type of "bevel", and the terms are often used interchangeably.
In furniture-making, a lark's tongue is a chamfer which ends short of a piece in a gradual upward curve, leaving the remainder of the edge as a right angle. Chamfers may be formed in either inside or outside adjoining faces of an object or room.
Carpentry and furniture
Chamfers are used in furniture such as counters and table tops to ease their edges to keep people from bruising themselves in the otherwise sharp corner. When the edges are rounded instead, they are called bullnosed. Special tools such as chamfer mills and chamfer planes are sometimes used.
Chamfers are commonly used in architecture, both for functional and aesthetic reasons. For example, the base of the Taj Mahal is a cube with chamfered corners, thereby creating an octagonal architectural footprint. Its great gate is formed of chamfered base stones and chamfered corbels for a balcony or equivalent cornice towards the roof.
Many city blocks in Barcelona, Valencia and various other cities in Spain, and street corners (curbs) in Ponce, Puerto Rico, are chamfered. The chamfering was designed as an embellishment and a modernization of urban space in Barcelona's mid-19th century Eixample or Expansion District, where the buildings follow the chamfering of the sidewalks and streets. This pioneering design opens up broader perspectives, provides pleasant pedestrian areas and allows for greater visibility while turning. It might also be considered to allow for turning to be somewhat more comfortable as, supposedly, drivers would not need to slow down as much when making a turn as they would have to if the corner were a square 90 degrees, though in Barcelona, most chamfered corners are used as parking spaces or loading-unloading zones, leaving the traffic to run as in normal 90-degree street corners.
The Great gate (Darwaza-i rauza) gateway to the Taj Mahal, having chamfered tower corners
The original Barcelona Eixample city block design, showing the chamfered corners of buildings and streets, and including gardens that never materialized.
Chamfers are frequently used to facilitate assembly of parts which are designed for interference fit or to aid assembly for parts inserted by hand. Resilient materials such as fluid power seals generally require a shallower angle than 45 degrees, often 20. In assemblies, chamfers are also used to clear an interior radius - perhaps from a cutting tool, or to clear other features, such as a weld bead, on an adjoining part. This is because it is generally easier to manufacture and much easier to precisely check the dimensions of a chamfer than a radius, and errors in the profile of either radius could otherwise cause interference between the radii before the flat surfaces make contact with one another. Chamfers are also essential for components which humans will handle, to prevent injuries, and also to prevent damage to other components. This is particularly important for hard materials, like most metals, and for heavy assemblies, like press tools. Additionally, a chamfered edge is much more resistant than a square edge to being bruised by other edges or corners knocking against it during assembly or disassembly, or maintenance.
In machining a chamfer is a slope cut at any right-angled edge of a workpiece, e.g. holes; the ends of rods, bolts, and pins; the corners of the long-edges of plates; any other place where two surfaces meet at a sharp angle. Chamfering eases assembly, e.g. the insertion of bolts into holes, or nuts. Chamfering also removes sharp edges which reduces significantly the possibility of cuts, and injuries, to people handling the metal piece.
Glass mirror design
Outside of aesthetics, chamfering is part of the process of hand-crafting a parabolic glass telescope mirror. Before the surface of the disc can be ground, the edges must first be chamfered to prevent edge chipping. This can be accomplished by placing the disc in a metal bowl containing silicon carbide and rotating the disc with a rocking motion. The grit will thus wear off the sharp edge of the glass.
Printed circuit board (PCB) design
In traditional printed circuit board (PCB) designing, a chamfer may be applied to a right-angled edge of a conductive junction in order to physically strengthen the conductive foil at that location. Chamfering of junctions may also be applied in high-frequency PCB design in order to reduce reflections. In high-voltage engineering, chamfers and rounded edges are used to reduce corona discharge and electrical breakdown.
- Madsen et al., "Engineering Drawing and Design" page 179. Delmar, 2004 ISBN 0-7668-1634-6
- "Interior Decoration". Government of UP, Uttar Pradesh. Retrieved 2014-04-05.
- "How to Build a Telescope ?". IUCAA SciPOP. Retrieved 2017-12-31.
- Bogatin, Eric. "When to worry about trace corners: Rule of Thumb #24". EDN Network. UBM Canon. Retrieved 8 June 2015.