In railroad structures, and rail terminology, a wye (like the 'Y' glyph) or triangular junction is a triangular joining arrangement of three rail lines with a railroad switch (set of points) at each corner connecting to each incoming line. A turning wye is a specific case.
Where two rail lines join, or in a joint between a railroad's mainline and a spur, wyes can be used as a mainline rail junction to allow incoming consists ability to travel either direction, or in order to allow trains to pass from one line to the other line.
Wyes can also be used for turning railway equipment, and generally cover less area than a balloon loop doing the same job but at the cost of two additional sets of points to construct, then maintain. These turnings are accomplished by performing the railway equivalent of a three-point turn through successive junctions of the wye, the direction of travel and the relative orientation of a locomotive or railway vehicle can be reversed, resulting in it facing in the direction from which it came. When and where a wye is built specifically for equipment reversing purposes, one or more of the tracks making up the junction will typically be a stub siding. In materials and annual taxes, the cost of two junctions is offset by saved capital investment and yearly taxes.
Tram or streetcar tracks also make use of triangular junctions and sometimes have a short triangle or wye stubs to turn the car at the end of the line.
- 1 Considerations
- 2 Earliest examples
- 3 Examples by country
- 4 Convoluted wye
- 5 See also
- 6 References
The use of triangular junctions allows flexibility in routing trains from any line to any other line, without the need to reverse the train. For this reason they are common across most rail networks. Slower bi-directional trains may enter a wye, letting a faster one pass, and continue on the same direction providing service to nearby freight transport or a passenger station.
Where one or more of the lines meeting at the junction are multi-track, the presence of a triangular junction does introduce a number of potential conflicting moves. For this reason, where traffic is heavy, the junction may incorporate flying junctions on some, or all, or the legs of the triangle.
For turning equipment
From time to time it is necessary to turn both individual pieces of railroad equipment or whole trains. This may be because the piece of equipment is not directionally symmetrical, for example in the case of most steam locomotives and, in certain parts of the world, diesel locomotives, or where the train needs to run a particular direction, for example where it has dedicated tail end car such as an observation car. Even where equipment is symmetrical, periodic turning may still be necessary in order to even wear.
There are several different techniques that can be used to achieve such turning. Railway turntables require the least space, but can generally only deal with a single piece of equipment at a time. Balloon or turning loops can turn trains of any length – up to the total length of the loop – in a single operation, but require far more space than wyes. Rail wyes can be constructed on sites where a loop would not be possible, and can turn trains up to the length of the stub tracks at the end of the wye.
Railroad systems in North America and Australia have tended to have more wyes than railroads elsewhere. North American locomotives and cars (such as observation cars) are more likely to be directional than those found on other continents. In Canada and the United States, the railroad often was built before other structures, and railway builders had much more freedom to lay down tracks where they wished. Similarly many early Australian railways made use of wyes (particularly in rural locations) for their lower installation and maintenance costs when not constrained by space limitations, though the major trend in most states toward bidirectional locomotives and railcars from the 1960s onwards saw their necessity and use diminish.
In Europe, although some use was made of bi-directional tank locomotives and push–pull trains, most steam locomotives were uni-directional. Because of land usage considerations, turntables were normally used to turn such locomotives, and most terminal stations and locomotive depots were so equipped. Over time, most diesel and electric locomotives ordered in Europe have been designed to be fully bi-directional, symmetrical, and normally with two driving cabs. Thus most turntables and, where they existed, rail wyes, have been taken out of use.
Streetcar or tram systems
Similar considerations apply to the use of triangular junctions and reversing wyes on streetcar and tram systems, as apply to mainline rail systems. Many, although by no means all, streetcar and tram systems use single ended vehicles that have doors on one side only, and that must be turned at each end of the route.
However the vehicles used on such systems tend to have much smaller minimum curvature requirements than heavy rail equipment. This renders the use of a balloon loop more practical in a small amount of space, and with street-running vehicles such a loop can make use of side streets or street squares. However, although turning loops are the most common way of turning such vehicles, wye tracks are also sometimes used.
A triangle may have a situational disadvantage in train operations when space constraints and routing of the local geography means taking the triangle connects to a desired destination, but locally bypasses a main station. In tight city environments, this can happen easily, as it did, for example, at Cootamundra West, Australia and Tecuci, Romania, where an extra passenger station had to be built to serve trains taking the shortcut.
In contrast, the engineering of a terminus station such as Woodville Railway Station, New Zealand avoided this problem by building a balloon loop (reversing loop) so that trains can serve the main station in either direction without the need to reverse. In a midline station where it is desired to reverse a consist or locomotive, a double-track and turning wye arrangement are far more common.
The land within a triangle is cut off from the adjacent area (and normally fenced off) and has marginal value, so will be purposed mainly for the railways exclusive use – generally be used for maintenance depots, storage, or vehicle parking. The triangular shape tends to be unsuited for rectangular buildings. On electrified lines substations tend to be located inside triangles, in part because the land is cheap, and also because it provides the most convenient and flexible sectioning arrangements.
The earliest British (and possibly worldwide) example is the double-tracked triangle within Earlestown railway station on the Liverpool and Manchester Railway, which was completed by the Grand Junction Railway in 1837. The triangle has two passenger platform faces on each of its three sides and five of the six platforms are in frequent (half-hourly etc.) use by passenger trains. When steam engines were in regular use the triangle (which is of course also traversed by freight trains) was also used to turn locomotives and can still be so used.
There is an example on the Cromford and High Peak Railway, which was opened in 1831 as a horse-drawn railway, which may be earlier. This appears to have been used for reversing trains of wagons with end doors that have just come up the rope-hauled inclines to the highest level of the railway before they proceeded down the remaining inclines. The site of this can still be seen near Hindlow, in Derbyshire, .
Examples by country
Sefton railway station, Sydney lies on one corner of a triangular junction. The triangle junction allows trains to branch off in either direction, without the need to terminate or change end. One train a day from Birrong to Sefton does terminate and reverse at Regents Park station (in order to clean the rust off the crossover rails). There is a goods branch from Chullora, and in the future the possibility of a proposed separate single track freight line. The three passenger stations at the vertices of the triangle have island platforms which make it convenient to change trains. The sharp curves of the triangle and especially the turnouts on those sharp curves restrict train movement speeds to between 10 km/h and 50 km/h.
Triangular junctions were built on the Victorian Railways Network both for turning of train consists and for major junctions. These included:
- Wodonga – Built on the junction of the Cudgewa Line and used to turn the consists of the Sydney Limited and Spirit of Progress trains.
- North Geelong – built to allow trains to travel directly between Geelong, Ballarat or Melbourne without using a run-around or turntable. Also used to turn trains such as demonstration run of the Spirit of Progress.
In the Republic of Ireland, there are currently two triangular junctions in use. One is at Limerick Junction, and the other at Lavistown, near Kilkenny. The former allows direct Limerick–Dublin passenger trains to bypass Limerick Junction station, and is also occasionally used to turn steam locomotives on railtours, whilst the latter is used primarily by freight trains running between the Port of Waterford and County Mayo to avoid having to run around in Kilkenny station.
In Belfast, Northern Ireland, a triangular junction exists at Great Victoria Street station. It is rarely used to turn locomotives, save the occasional steam engine. Usually, it is used by Enterprise express trains to bypass Great Victoria Street and continue on and terminate at Belfast Central. Commuter trains enter the junction from one direction (e.g. the Portadown line), stop at Great Victoria Street, and then continue out on the other direction towards Bangor station. Commuter trains on NI Railways are all diesel multiple unit railcars, so they do not need to use the junction as a turning method.
The only other operational triangular junction in Ireland is Downpatrick Loop on the Downpatrick and County Down Railway. Originally constructed to allow direct Belfast–Newcastle trains to bypass Downpatrick station, the triangle today forms the basis of a heritage railway, the only heritage railway of this type in the British Isles. There is one station at each end of the triangle and another in the southernmost corner.
Historical triangular junctions in Ireland include Moyasta Junction on the West Clare line, the Monkstown/Greenisland/Bleach Green triangle on the Northern Counties Committee and Bundoran Junction on the Great Northern Railway. Though two sides of the former are still in mainline use, the 'back line' between Monkstown and Greenisland has been removed, whilst the latter was closed altogether in 1957. Additionally, the Great Northern's largest locomotive yard at Adelaide never had a turntable, using a dedicated turning triangle instead.
Railways in Italy used a number of 'inversion stars' for turning locomotives. This uses a pentagram layout, requiring four movements and three turnouts to reverse. It allows a smaller layout, without excessively tight curve radii, compared to a triangle.
Tsumeb railway station in Namibia has two triangles. The first and smaller one is for turning engines and is near the station. The second and larger one is to bypass the dead-end station at Tsumeb for trains travelling directly between the new extension towards Angola and Windhoek. This direct bypass line can save an hour of shunting time, particularly if the train is longer than the loops in the station.
There is a turning triangle partly tunnelled into the mountain at Kleine Scheidegg at the summit of the 800mm gauge Wengernalpbahn in the Bernese Oberland, Switzerland. Kleine Scheidegg is reached from two lower termini, Lauterbrunnen and Grindelwald, located on opposite sides of the col. Trains normally descend in the direction they have arrived from and are designed accordingly with the power unit at the lower end and seating angled to compensate for the gradient. They therefore have to be turned at the summit should it be necessary to make a through journey. Whilst limitations of space dictated that the triangle had to be partly constructed in tunnels it also ensures that in winter it is snow-free and is readily available in emergencies.
In Britain triangular layouts that could be used for turning locomotives were usually the result of junctions of two or more lines. There are many examples, including the one known as the Maindee triangle in Newport, South Wales. Here the ex-GWR South Wales mainline from London to Swansea is joined by another GWR line from Shrewsbury via Hereford. The significance of it is that steam-hauled trains can run to Newport and their engines be turned using the triangle. Its National Grid location is grid reference . Shrewsbury also has a triangular route formation that was used to turn steam locomotives, and is still available. A triangle, grid reference , was provided in 1989 adjacent to the transfer sidings for Wylfa Nuclear Power Station, near to Valley on Anglesey in Wales. This enables the North Wales Coast Line to be used by steam hauled excursions. The turntable at Holyhead has long been removed and the area re-developed and the sidings at Valley some 4 miles (6.4 km) from the terminus are the nearest suitable site.
An unusual arrangement, unique in Britain, was constructed at Grantham. Its location was grid reference and it is shown on the 1963 edition of OS 1 inch to 1 mile sheet 113. It was built in the 1950s after the turntable at the locomotive shed failed and expenditure on a replacement was no longer justified. Locomotives requiring to be turned had to travel to Barkston Junction to traverse the triangular layout there (this was where Mallard with a dynamometer car attached was turned before starting out south on its record-breaking run on 3 July 1938). The journey to Barkston Junction and back was a time-consuming business involving a round trip of some 8 miles (13 km) along the busy East Coast Main Line. Eventually authority was given to construct a turning arrangement on a strip of spare land to the west of the main line, just south of Grantham station. There was insufficient space for a conventional triangle but this was overcome by constructing an 'inside-out' triangle whereby the approach tracks intersected in a scissors crossing.
Many North American passenger terminals in large cities had wye tracks to allow the turning and backing of directional passenger trains onto a main line. Freight traffic could bypass the terminal through the wye. Notable examples include the Los Angeles Union Station, which has a double wye, the Saint Paul Union Depot, and the Memphis Union Station.
A typical use for a stub-end passenger station would be as follows: A wye was incorporated at the 'throat' where the rows of tracks converged from the station. It facilitated the turning of trains. Each arriving train passed the wye and came to a stop. Once the switches on the wye are aligned, the train reversed, with the brakeman at the rear of the last car regulating the speed with the brake lever upon approach to the platform and then coming to a complete stop at the end of the track, shutting the air brakes completely. Passengers were then allowed to safely disembark.
Meanwhile, the locomotives were uncoupled from the train and sent to the engine terminal to be serviced for their next assignment. Then, the head-end cars were uncoupled from the rest of the train and pulled by a station switcher to a parcel facility where express packages were unloaded. The departing train was reassembled, freshly cleaned and serviced for the next journey. A steam pipe from the station's steam generator was attached to the train's steam line from the rear to supply heat until the locomotives were coupled up front to supply steam.
The train was announced for boarding with a list of destinations. With switches aligned, the train slowly departed to the main line, rounding the opposite leg from the one it reversed on upon arrival. The train returned to the place it arrived from.
The Keddie Wye in Keddie, California, was built by the Western Pacific Railroad and is a remarkable engineering feat. Two sides of the wye are built on tall trestles and one side is a tunnel bored through solid rock.
The southern terminus of the Amtrak Auto Train in Sanford, Florida, uses a wye to turn the locomotives around for the trip back north. A road that crosses the eastern side of the wye allows access to the inner part of the wye where a rock supply company now stands.
In Arizona, the Grand Canyon Railway (GCRY) has a wye at both the Williams and South Rim/Grand Canyon Village termini of its line. The train is turned around at the South Rim/Grand Canyon Village wye with the passengers onboard. At the Williams end, the train is turned around after the passengers disembark.
Convoluted wye, turning star or reversing star (Italian: Stella di inversione) is a special wye layout used in places where the space is tight. It has a pentagram-like form and consists of five turnouts (versus three for a wye) and three diamond crossings. Because of this, a reversing star is more expensive to build and service.
It takes four changes of direction of movement to turn a piece of rolling stock on a reversing star.
- "UFC 4-860-01FA Railroad Design and Rehabilitation" (PDF). Unified Facilities Criteria (UFC). U.S. Department of Defense. 16 January 2004. pp. 8–12. Archived from the original (PDF) on 15 December 2011. Retrieved 23 December 2011.
- Kay, Peter (1997). The Cromford & High Peak Railway: Part 2 – Memories of the High Peak. Stafford, Robert Cartwright Productions. DVD.
- Marshall, John (1982). The Cromford & High Peak Railway. Newton Abbot, Devon; and North Pomfret, Vermont: David & Charles. ISBN 978-0-715-38128-1. p. 36.
- "Via della Stazione, Carbonia CI, Italy". Google Maps.
- .[dead link] DigitalGlobe.