**Enthalpy** /ˈɛnθəlpi/ (listen) is a property of a thermodynamic system, defined as the sum of the system's internal energy and the product of its pressure and volume.^{[1]}^{[2]}
It is a convenient state function standardly used in many measurements in chemical, biological, and physical systems at a constant pressure. The pressure-volume term expresses the work required to establish the system's physical dimensions, i.e. to make room for it by displacing its surroundings.^{[3]}^{[4]} As a state function, enthalpy depends only on the final configuration of internal energy, pressure, and volume, not on the path taken to achieve it.

The unit of measurement for enthalpy in the International System of Units (SI) is the joule. Other historical conventional units still in use include the British thermal unit (BTU) and the calorie.

The total enthalpy of a system cannot be measured directly because the internal energy contains components that are unknown, not easily accessible, or are not of interest in thermodynamics. In practice, a change in enthalpy (Δ*H*) is the preferred expression for measurements at constant pressure, because it simplifies the description of energy transfer. When matter transfer into or out of the system is also prevented, the enthalpy change equals the energy exchanged with the environment by heat. Calibration of enthalpy changes requires a reference point. Enthalpies for chemical substances at constant pressure usually refer to standard state: most commonly 1 bar (100 kPa) pressure. Standard state does not strictly specify a temperature, but expressions for enthalpy generally reference the standard heat of formation at 25 °C (298 K). For endothermic (heat-absorbing) processes, the change Δ*H* is a positive value; for exothermic (heat-releasing) processes it is negative.

The enthalpy of an ideal gas is independent of its pressure, and depends only on its temperature, which correlates to its internal energy. Real gases at common temperatures and pressures often closely approximate this behavior, which simplifies practical thermodynamic design and analysis.

## Definition

The enthalpy *H* of a thermodynamic system is defined as the sum of its internal energy *U* and the work required to achieve its pressure and volume:^{[5]}^{[6]}

*H*=*U*+*pV*,

where p is pressure, and V is the volume of the system.

Enthalpy is an extensive property; it is proportional to the size of the system (for homogeneous systems). As intensive properties, the specific enthalpy *h* = *H*/*m* is referenced to a unit of mass m of the system, and the molar enthalpy *H*_{m} is *H*/*n*, where n is the number of moles. For inhomogeneous systems the enthalpy is the sum of the enthalpies of the composing subsystems:

where

- H is the total enthalpy of all the subsystems,
- k refers to the various subsystems,
- H
_{k}refers to the enthalpy of each subsystem.

A closed system may lie in thermodynamic equilibrium in a static gravitational field, so that its pressure p varies continuously with altitude, while, because of the equilibrium requirement, its temperature T is invariant with altitude. (Correspondingly, the system's gravitational potential energy density also varies with altitude.) Then the enthalpy summation becomes an integral:

where

- ρ ("rho") is density (mass per unit volume),
- h is the specific enthalpy (enthalpy per unit mass),
- (
*ρh*) represents the enthalpy density (enthalpy per unit volume), - dV denotes an infinitesimally small element of volume within the system, for example, the volume of an infinitesimally thin horizontal layer,
- the integral therefore represents the sum of the enthalpies of all the elements of the volume.

The enthalpy of a closed homogeneous system is its cardinal energy function *H*(*S*,*p*), with natural state variables its entropy *S*[*p*] and its pressure p. A differential relation for it can be derived as follows. We start from the first law of thermodynamics for closed systems for an infinitesimal process:

where

- Δ
*Q*is a small amount of heat added to the system, - Δ
*W*is a small amount of work performed by the system.

In a homogeneous system in which only reversible, or quasi-static, processes are considered, the second law of thermodynamics gives Δ*Q* = *T* *dS*, with T the absolute temperature and dS the infinitesimal change in entropy S of the system. Furthermore, if only pV work is done, Δ*W* = *p* *dV*. As a result,

Adding *d*(*pV*) to both sides of this expression gives

or

So

## Other expressions

The above expression of dH in terms of entropy and pressure may be unfamiliar to some readers. However, there are expressions in terms of more familiar variables such as temperature and pressure:^{[5]}^{:88}^{[7]}

Here *C*_{p} is the heat capacity at constant pressure and α is the coefficient of (cubic) thermal expansion:

With this expression one can, in principle, determine the enthalpy if C_{p} and V are known as functions of p and T.

Note that for an ideal gas, *αT* = 1,^{[note 1]} so that

In a more general form, the first law describes the internal energy with additional terms involving the chemical potential and the number of particles of various types. The differential statement for dH then becomes

where *μ*_{i} is the chemical potential per particle for an i-type particle, and *N*_{i} is the number of such particles. The last term can also be written as *μ _{i}*

*dn*

_{i}(with

*dn*

_{i}the number of moles of component i added to the system and, in this case,

*μ*

_{i}the molar chemical potential) or as

*μ*

_{i}

*dm*

_{i}(with

*dm*

_{i}the mass of component i added to the system and, in this case,

*μ*

_{i}the specific chemical potential).

### Cardinal functions

The enthalpy, *H*(*S*[*p*],*p*,{*N _{i}*}), expresses the thermodynamics of a system in the

*energy representation*. As a function of state, its arguments include both one intensive and several extensive state variables. The state variables

*S*[

*p*],

*p*, and {

*N*} are said to be the

_{i}*natural state variables*in this representation. They are suitable for describing processes in which they are experimentally controlled. For example, in an idealized process,

*S*[

*p*] and

*p*can be controlled by preventing heat and matter transfer by enclosing the system with a wall that is adiathermal and impermeable to matter, and by making the process infinitely slow, and by varying only the external pressure on the piston that controls the volume of the system. This is the basis of the so-called adiabatic approximation that is used in meteorology.

^{[8]}

Alongside the enthalpy, with these arguments, the other cardinal function of state of a thermodynamic system is its entropy, as a function, *S*[*p*](*H*,*p*,{*N _{i}*}), of the same list of variables of state, except that the entropy,

*S*[

*p*], is replaced in the list by the enthalpy,

*H*. It expresses the

*entropy representation*. The state variables

*H*,

*p*, and {

*N*} are said to be the

_{i}*natural state variables*in this representation. They are suitable for describing processes in which they are experimentally controlled. For example,

*H*and

*p*can be controlled by allowing heat transfer, and by varying only the external pressure on the piston that sets the volume of the system.

^{[9]}

^{[10]}

^{[11]}

## Physical interpretation

The U term can be interpreted as the energy required to create the system, and the pV term as the work that would be required to "make room" for the system if the pressure of the environment remained constant. When a system, for example, n moles of a gas of volume V at pressure p and temperature T, is created or brought to its present state from absolute zero, energy must be supplied equal to its internal energy U plus pV, where pV is the work done in pushing against the ambient (atmospheric) pressure.

In basic physics and statistical mechanics it may be more interesting to study the internal properties of the system and therefore the internal energy is used.^{[12]}^{[13]} In basic chemistry, experiments are often conducted at constant atmospheric pressure, and the pressure-volume work represents an energy exchange with the atmosphere that cannot be accessed or controlled, so that Δ*H* is the expression chosen for the heat of reaction.

For a heat engine a change in its internal energy is the difference between the heat input and the pressure-volume work done by the working substance while a change in its enthalpy is the difference between the heat input and the work done by the engine:^{[14]}

where the work W done by the engine is:

## Relationship to heat

In order to discuss the relation between the enthalpy increase and heat supply, we return to the first law for closed systems, with the physics sign convention: *dU* = *δQ* − *δW*, where the heat δQ is supplied by conduction, radiation, and Joule heating. We apply it to the special case with a constant pressure at the surface. In this case the work term can be split into two contributions, the so-called pV work, given by *p dV* (where here p is the pressure at the surface, dV is the increase of the volume of the system), and the so-called isochoric mechanical work δW′, such as stirring by a shaft with paddles or by an externally driven magnetic field acting on an internal rotor. Cases of long range electromagnetic interaction require further state variables in their formulation, and are not considered here. So we write *δW* = *p dV* + *δW′*. In this case the first law reads:

Now,

So

With sign convention of physics, *δW'* < 0, because isochoric shaft work done by an external device on the system adds energy to the system, and may be viewed as virtually adding heat. The only thermodynamic mechanical work done by the system is expansion work, *p dV*.^{[15]}

The system is under constant pressure (*dp* = 0). Consequently, the increase in enthalpy of the system is equal to the added heat and virtual heat:

This is why the now-obsolete term *heat content* was used in the 19th century.

## Applications

In thermodynamics, one can calculate enthalpy by determining the requirements for creating a system from "nothingness"; the mechanical work required, pV, differs based upon the conditions that obtain during the creation of the thermodynamic system.

Energy must be supplied to remove particles from the surroundings to make space for the creation of the system, assuming that the pressure p remains constant; this is the pV term. The supplied energy must also provide the change in internal energy, U, which includes activation energies, ionization energies, mixing energies, vaporization energies, chemical bond energies, and so forth. Together, these constitute the change in the enthalpy *U* + *pV*. For systems at constant pressure, with no external work done other than the pV work, the change in enthalpy is the heat received by the system.

For a simple system, with a constant number of particles, the difference in enthalpy is the maximum amount of thermal energy derivable from a thermodynamic process in which the pressure is held constant.^{[16]}

### Heat of reaction

The total enthalpy of a system cannot be measured directly; the *enthalpy change* of a system is measured instead. Enthalpy change is defined by the following equation:

where

- Δ
*H*is the "enthalpy change", *H*_{f}is the final enthalpy of the system (in a chemical reaction, the enthalpy of the products),*H*_{i}is the initial enthalpy of the system (in a chemical reaction, the enthalpy of the reactants).

For an exothermic reaction at constant pressure, the system's change in enthalpy equals the energy released in the reaction, including the energy retained in the system and lost through expansion against its surroundings. In a similar manner, for an endothermic reaction, the system's change in enthalpy is equal to the energy *absorbed* in the reaction, including the energy *lost by* the system and *gained* from compression from its surroundings. If Δ*H* is positive, the reaction is endothermic, that is heat is absorbed by the system due to the products of the reaction having a greater enthalpy than the reactants. On the other hand, if Δ*H* is negative, the reaction is exothermic, that is the overall decrease in enthalpy is achieved by the generation of heat.^{[17]}

From the definition of enthalpy as *H* = *U* + *pV*, the enthalpy change at constant pressure Δ*H* = Δ*U* + *p* Δ*V*. However for most chemical reactions, the work term *p* Δ*V* is much smaller than the internal energy change Δ*U* which is approximately equal to Δ*H*. As an example, for the combustion of carbon monoxide 2 CO(g) + O_{2}(g) → 2 CO_{2}(g), Δ*H* = −566.0 kJ and Δ*U* = −563.5 kJ.^{[18]} Since the differences are so small, reaction enthalpies are often loosely described as reaction energies and analyzed in terms of bond energies.

### Specific enthalpy

The specific enthalpy of a uniform system is defined as *h* = *H*/*m* where m is the mass of the system. The SI unit for specific enthalpy is joule per kilogram. It can be expressed in other specific quantities by *h* = *u* + *pv*, where u is the specific internal energy, p is the pressure, and v is specific volume, which is equal to 1/*ρ*, where ρ is the density.

### Enthalpy changes

An enthalpy change describes the change in enthalpy observed in the constituents of a thermodynamic system when undergoing a transformation or chemical reaction. It is the difference between the enthalpy after the process has completed, i.e. the enthalpy of the products, and the initial enthalpy of the system, namely the reactants. These processes are reversible^{[why?]} and the enthalpy for the reverse process is the negative value of the forward change.

A common standard enthalpy change is the enthalpy of formation, which has been determined for a large number of substances. Enthalpy changes are routinely measured and compiled in chemical and physical reference works, such as the CRC Handbook of Chemistry and Physics. The following is a selection of enthalpy changes commonly recognized in thermodynamics.

When used in these recognized terms the qualifier *change* is usually dropped and the property is simply termed *enthalpy of 'process'*. Since these properties are often used as reference values it is very common to quote them for a standardized set of environmental parameters, or standard conditions, including:

- A temperature of 25 °C or 298.15 K,
- A pressure of one atmosphere (1 atm or 101.325 kPa),
- A concentration of 1.0 M when the element or compound is present in solution,
- Elements or compounds in their normal physical states, i.e. standard state.

For such standardized values the name of the enthalpy is commonly prefixed with the term *standard*, e.g. *standard enthalpy of formation*.

Chemical properties:

- Enthalpy of reaction, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of substance reacts completely.
- Enthalpy of formation, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a compound is formed from its elementary antecedents.
- Enthalpy of combustion, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a substance burns completely with oxygen.
- Enthalpy of hydrogenation, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of an unsaturated compound reacts completely with an excess of hydrogen to form a saturated compound.
- Enthalpy of atomization, defined as the enthalpy change required to atomize one mole of compound completely.
- Enthalpy of neutralization, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of water is formed when an acid and a base react.
- Standard Enthalpy of solution, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a solute is dissolved completely in an excess of solvent, so that the solution is at infinite dilution.
- Standard enthalpy of Denaturation (biochemistry), defined as the enthalpy change required to denature one mole of compound.
- Enthalpy of hydration, defined as the enthalpy change observed when one mole of gaseous ions are completely dissolved in water forming one mole of aqueous ions.

Physical properties:

- Enthalpy of fusion, defined as the enthalpy change required to completely change the state of one mole of substance between solid and liquid states.
- Enthalpy of vaporization, defined as the enthalpy change required to completely change the state of one mole of substance between liquid and gaseous states.
- Enthalpy of sublimation, defined as the enthalpy change required to completely change the state of one mole of substance between solid and gaseous states.
- Lattice enthalpy, defined as the energy required to separate one mole of an ionic compound into separated gaseous ions to an infinite distance apart (meaning no force of attraction).
- Enthalpy of mixing, defined as the enthalpy change upon mixing of two (non-reacting) chemical substances.

### Open systems

In thermodynamic open systems, mass (of substances) may flow in and out of the system boundaries. The first law of thermodynamics for open systems states: The increase in the internal energy of a system is equal to the amount of energy added to the system by mass flowing in and by heating, minus the amount lost by mass flowing out and in the form of work done by the system:

where *U*_{in} is the average internal energy entering the system, and *U*_{out} is the average internal energy leaving the system.

The region of space enclosed by the boundaries of the open system is usually called a control volume, and it may or may not correspond to physical walls. If we choose the shape of the control volume such that all flow in or out occurs perpendicular to its surface, then the flow of mass into the system performs work as if it were a piston of fluid pushing mass into the system, and the system performs work on the flow of mass out as if it were driving a piston of fluid. There are then two types of work performed: *flow work* described above, which is performed on the fluid (this is also often called *pV work*), and *shaft work*, which may be performed on some mechanical device.

These two types of work are expressed in the equation

Substitution into the equation above for the control volume (cv) yields:

The definition of enthalpy, H, permits us to use this thermodynamic potential to account for both internal energy and pV work in fluids for open systems:

If we allow also the system boundary to move (e.g. due to moving pistons), we get a rather general form of the first law for open systems.^{[19]} In terms of time derivatives it reads:

with sums over the various places k where heat is supplied, mass flows into the system, and boundaries are moving. The Ḣ_{k} terms represent enthalpy flows, which can be written as

with ṁ_{k} the mass flow and ṅ_{k} the molar flow at position k respectively. The term *dV*_{k}/*dt* represents the rate of change of the system volume at position k that results in pV power done by the system. The parameter *P* represents all other forms of power done by the system such as shaft power, but it can also be, say, electric power produced by an electrical power plant.

Note that the previous expression holds true only if the kinetic energy flow rate is conserved between system inlet and outlet.^{[clarification needed]} Otherwise, it has to be included in the enthalpy balance. During steady-state operation of a device (*see turbine, pump, and engine*), the average *dU*/*dt* may be set equal to zero. This yields a useful expression for the average power generation for these devices in the absence of chemical reactions:

where the angle brackets denote time averages. The technical importance of the enthalpy is directly related to its presence in the first law for open systems, as formulated above.

## Diagrams

The enthalpy values of important substances can be obtained using commercial software. Practically all relevant material properties can be obtained either in tabular or in graphical form. There are many types of diagrams, such as *h*–*T* diagrams, which give the specific enthalpy as function of temperature for various pressures, and *h*–*p* diagrams, which give h as function of p for various T. One of the most common diagrams is the temperature–specific entropy diagram (*T*–*s* diagram). It gives the melting curve and saturated liquid and vapor values together with isobars and isenthalps. These diagrams are powerful tools in the hands of the thermal engineer.

### Some basic applications

The points **a** through **h** in the figure play a role in the discussion in this section.

Point T (K) p (bar) s (kJ/(kg K)) h (kJ/kg) **a**300 1 6.85 461 **b**380 2 6.85 530 **c**300 200 5.16 430 **d**270 1 6.79 430 **e**108 13 3.55 100 **f**77.2 1 3.75 100 **g**77.2 1 2.83 28 **h**77.2 1 5.41 230

Points **e** and **g** are saturated liquids, and point **h** is a saturated gas.

### Throttling

One of the simple applications of the concept of enthalpy is the so-called throttling process, also known as Joule-Thomson expansion. It concerns a steady adiabatic flow of a fluid through a flow resistance (valve, porous plug, or any other type of flow resistance) as shown in the figure. This process is very important, since it is at the heart of domestic refrigerators, where it is responsible for the temperature drop between ambient temperature and the interior of the refrigerator. It is also the final stage in many types of liquefiers.

For a steady state flow regime, the enthalpy of the system (dotted rectangle) has to be constant. Hence

Since the mass flow is constant, the specific enthalpies at the two sides of the flow resistance are the same:

that is, the enthalpy per unit mass does not change during the throttling. The consequences of this relation can be demonstrated using the *T*–*s* diagram above. Point **c** is at 200 bar and room temperature (300 K). A Joule–Thomson expansion from 200 bar to 1 bar follows a curve of constant enthalpy of roughly 425 kJ/kg (not shown in the diagram) lying between the 400 and 450 kJ/kg isenthalps and ends in point **d**, which is at a temperature of about 270 K. Hence the expansion from 200 bar to 1 bar cools nitrogen from 300 K to 270 K. In the valve, there is a lot of friction, and a lot of entropy is produced, but still the final temperature is below the starting value.

Point **e** is chosen so that it is on the saturated liquid line with *h* = 100 kJ/kg. It corresponds roughly with *p* = 13 bar and *T* = 108 K. Throttling from this point to a pressure of 1 bar ends in the two-phase region (point **f**). This means that a mixture of gas and liquid leaves the throttling valve. Since the enthalpy is an extensive parameter, the enthalpy in **f** (*h*_{f}) is equal to the enthalpy in **g** (*h*_{g}) multiplied by the liquid fraction in **f** (*x*_{f}) plus the enthalpy in **h** (*h*_{h}) multiplied by the gas fraction in **f** (1 − *x*_{f}). So

With numbers: 100 = *x*_{f} × 28 + (1 − *x*_{f}) × 230, so *x*_{f} = 0.64. This means that the mass fraction of the liquid in the liquid–gas mixture that leaves the throttling valve is 64%.

### Compressors

A power P is applied e.g. as electrical power. If the compression is adiabatic, the gas temperature goes up. In the reversible case it would be at constant entropy, which corresponds with a vertical line in the *T*–*s* diagram. For example, compressing nitrogen from 1 bar (point **a**) to 2 bar (point **b**) would result in a temperature increase from 300 K to 380 K. In order to let the compressed gas exit at ambient temperature *T*_{a}, heat exchange, e.g. by cooling water, is necessary. In the ideal case the compression is isothermal. The average heat flow to the surroundings is Q̇. Since the system is in the steady state the first law gives

The minimal power needed for the compression is realized if the compression is reversible. In that case the second law of thermodynamics for open systems gives

Eliminating Q̇ gives for the minimal power

For example, compressing 1 kg of nitrogen from 1 bar to 200 bar costs at least (*h*_{c} − *h*_{a}) − *T*_{a}(*s*_{c} − *s*_{a}). With the data, obtained with the *T*–*s* diagram, we find a value of (430 − 461) − 300 × (5.16 − 6.85) = 476 kJ/kg.

The relation for the power can be further simplified by writing it as

With *dh* = *T* *ds* + *v* *dp*, this results in the final relation

## History

The term *enthalpy* was coined relatively late in the history of thermodynamics, in the early 20th century. Energy was introduced in a modern sense by Thomas Young in 1802, while entropy was coined by Rudolf Clausius in 1865. *Energy* uses the root of the Greek word ἔργον (*ergon*), meaning "work", to express the idea of capacity to perform work. *Entropy* uses the Greek word τροπή (*tropē*) meaning *transformation*. *Enthalpy* uses the root of the Greek word θάλπος (*thalpos*) "warmth, heat"^{[21]}

The term expresses the obsolete concept of *heat content*,^{[22]} as dH refers to the amount of heat gained in a process at constant pressure only,^{[23]} but not in the general case when pressure is variable.^{[24]}Josiah Willard Gibbs used the term "a heat function for constant pressure" for clarity.^{[note 2]}

Introduction of the concept of "heat content" H is associated with Benoît Paul Émile Clapeyron and Rudolf Clausius (Clausius–Clapeyron relation, 1850).

The term *enthalpy* first appeared in print in 1909.^{[25]} It is attributed to Heike Kamerlingh Onnes, who most likely introduced it orally the year before, at the first meeting of the Institute of Refrigeration in Paris.^{[26]}
It gained currency only in the 1920s, notably with the *Mollier Steam Tables and Diagrams*, published in 1927.

Until the 1920s, the symbol H was used, somewhat inconsistently, for "heat" in general.
The definition of H as strictly limited to enthalpy or "heat content at constant pressure" was formally proposed by Alfred W. Porter in 1922.^{[27]}^{[28]}

## See also

- Standard enthalpy change of formation (data table)
- Calorimetry
- Calorimeter
- Departure function
- Hess's law
- Isenthalpic process
- Laws of thermodynamics
- Stagnation enthalpy
- Thermodynamic databases for pure substances

## Notes

## References

**^**"Oxford Living Dictionaries". Archived from the original on 2016-08-17. Retrieved 2018-02-19.**^**"IUPAC Gold Book. Enthalpy,*H*". Retrieved 2018-02-19.**^**Zemansky, Mark W. (1968). "Chapter 11".*Heat and Thermodynamics*(5th ed.). New York, NY: McGraw-Hill. p. 275.**^**Van Wylen, G. J.; Sonntag, R. E. (1985). "Section 5.5".*Fundamentals of Classical Thermodynamics*(3rd ed.). New York: John Wiley & Sons. ISBN 978-0-471-82933-1.- ^
^{a}^{b}Guggenheim, E. A. (1959).*Thermodynamics*. Amsterdam: North-Holland Publishing Company. **^**Zumdahl, Steven S. (2008). "Thermochemistry".*Chemistry*. Cengage Learning. p. 243. ISBN 978-0-547-12532-9. Archived from the original on 2013-11-14.**^**Moran, M. J.; Shapiro, H. N. (2006).*Fundamentals of Engineering Thermodynamics*(5th ed.). John Wiley & Sons. p. 511.**^**Iribarne, J.V., Godson, W.L. (1981).*Atmospheric Thermodynamics*, 2nd edition, Kluwer Academic Publishers, Dordrecht, ISBN 90-277-1297-2, pp. 235–236.**^**Tschoegl, N.W. (2000).*Fundamentals of Equilibrium and Steady-State Thermodynamics*, Elsevier, Amsterdam, ISBN 0-444-50426-5, p. 17.**^**Callen, H. B. (1960/1985),*Thermodynamics and an Introduction to Thermostatistics*, (first edition 1960), second edition 1985, John Wiley & Sons, New York, ISBN 0-471-86256-8, Chapter 5.**^**Münster, A. (1970), Classical Thermodynamics, translated by E. S. Halberstadt, Wiley–Interscience, London, ISBN 0-471-62430-6, p. 6.**^**Reif, F. (1967).*Statistical Physics*. London: McGraw-Hill.**^**Kittel, C.; Kroemer, H. (1980).*Thermal Physics*. London: Freeman.**^**Bartelmann, Matthias (2015).*Theoretische Physik*. Springer Spektrum. pp. 1106–1108. ISBN 978-3-642-54617-4.**^**Ebbing, Darrel; Gammon, Steven (2010).*General Chemistry*. Cengage Learning. p. 231. ISBN 978-0-538-49752-7. Archived from the original on 2013-11-14.**^**Rathakrishnan (2015).*High Enthalpy Gas Dynamics*. John Wiley and Sons Singapore Pte. Ltd. ISBN 978-1118821893.**^**Laidler, Keith J.; Meiser, John H. (1982).*Physical Chemistry*. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.**^**Petrucci, Ralph H.; Harwood, William S.; Herring, F. Geoffrey (2002).*General Chemistry*(8th ed.). Prentice Hall. pp. 237–238. ISBN 978-0-13-014329-7.**^**Moran, M. J.; Shapiro, H. N. (2006).*Fundamentals of Engineering Thermodynamics*(5th ed.). John Wiley & Sons. p. 129.**^**Figure composed with data obtained with RefProp, NIST Standard Reference Database 23.**^**θάλπος in*A Greek–English Lexicon*.**^**Howard (2002) quotes J. R. Partington in*An Advanced Treatise on Physical Chemistry*(1949) as saying that the function*H*was "usually called the heat content".**^**Tinoco, Jr., Ignacio; Sauer, Kenneth; Wang, James C. (1995).*Physical Chemistry*(3rd ed.). Prentice-Hall. p. 41. ISBN 978-0-13-186545-7.**^**Laidler, Keith J.; Meiser, John H. (1982).*Physical Chemistry*. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.**^**Dalton, J. P. (1909). "Researches on the Joule-Kelvin-effect, especially at low temperatures. I. Calculations for hydrogen".*Proceedings of the Section of Sciences (Koninklijke Akademie van Wetenschappen Te Amsterdam [Royal Academy of Sciences at Amsterdam])*. 11 (part 2): 863–873. Bibcode:1908KNAB...11..863D. ; see p. 864, footnote (1).**^**See:- Laidler, Keith (1995).
*The World of Physical Chemistry*. Oxford University Press. p. 110. - Van Ness, Hendrick C. (2003). "
*H*Is for Enthalpy".*Journal of Chemical Education*.**80**(6): 486. Bibcode:2003JChEd..80..486V. doi:10.1021/ed080p486.1.

- Laidler, Keith (1995).
**^**Porter, Alfred W. (1922). "The generation and utilisation of cold. A general discussion".*Transactions of the Faraday Society*.**18**: 139–143. doi:10.1039/tf9221800139.; see p. 140.**^**Howard, Irmgard (2002). "*H*Is for Enthalpy, Thanks to Heike Kamerlingh Onnes and Alfred W. Porter".*Journal of Chemical Education*.**79**(6): 697. Bibcode:2002JChEd..79..697H. doi:10.1021/ed079p697.

## Bibliography

- Dalton, J.P. (1909). "Researches on the Joule–Kelvin effect, especially at low temperatures. I. Calculations for hydrogen" (PDF).
*KNAW Proceedings*.**11**: 863–873. Bibcode:1908KNAB...11..863D. - Haase, R. (1971). Jost, W. (ed.).
*Physical Chemistry: An Advanced Treatise*. New York: Academic. p. 29. - Gibbs, J. W.
*The Collected Works of J. Willard Gibbs, Vol. I*(1948 ed.). New Haven, CT: Yale University Press. p. 88. - Howard, I. K. (2002). "
*H*Is for Enthalpy, Thanks to Heike Kamerlingh Onnes and Alfred W. Porter".*J. Chem. Educ.***79**(6): 697–698. Bibcode:2002JChEd..79..697H. doi:10.1021/ed079p697. - Laidler, K. (1995).
*The World of Physical Chemistry*. Oxford: Oxford University Press. p. 110. - Kittel, C.; Kroemer, H. (1980).
*Thermal Physics*. New York: S. R. Furphy & Co. p. 246. - DeHoff, R. (2006).
*Thermodynamics in Materials Science*. CRC Press. ISBN 9780849340659.

## External links

- Enthalpy – Eric Weisstein's World of Physics
- Enthalpy – Georgia State University
- Enthalpy example calculations – Texas A&M University Chemistry Department