A space suit or spacesuit is a garment worn to keep a human alive in the harsh environment of outer space, vacuum and temperature extremes. Space suits are often worn inside spacecraft as a safety precaution in case of loss of cabin pressure, and are necessary for extravehicular activity (EVA), work done outside spacecraft. Space suits have been worn for such work in Earth orbit, on the surface of the Moon, and en route back to Earth from the Moon. Modern space suits augment the basic pressure garment with a complex system of equipment and environmental systems designed to keep the wearer comfortable, and to minimize the effort required to bend the limbs, resisting a soft pressure garment's natural tendency to stiffen against the vacuum. A self-contained oxygen supply and environmental control system is frequently employed to allow complete freedom of movement, independent of the spacecraft.
Three types of space suits exist for different purposes: IVA (intravehicular activity), EVA (extravehicular activity), and IEVA (intra/extravehicular activity). IVA suits are meant to be worn inside a pressurized spacecraft, and are therefore lighter and more comfortable. IEVA suits are meant for use inside and outside the spacecraft, such as the Gemini G4C suit. They include more protection from the harsh conditions of space, such as protection from micrometeorites and extreme temperature change. EVA suits, such as the EMU, are used outside spacecraft, for either planetary exploration or spacewalks. They must protect the wearer against all conditions of space, as well as provide mobility and functionality.
Some of these requirements also apply to pressure suits worn for other specialized tasks, such as high-altitude reconnaissance flight. At altitudes above the Armstrong limit, around 19,000 m (62,000 ft), water boils at body temperature and pressurized suits are needed.
The first full-pressure suits for use at extreme altitudes were designed by individual inventors as early as the 1930s. The first space suit worn by a human in space was the Soviet SK-1 suit worn by Yuri Gagarin in 1961.
A space suit must perform several functions to allow its occupant to work safely and comfortably, inside or outside a spacecraft. It must provide:
- A stable internal pressure. This can be less than Earth's atmosphere, as there is usually no need for the space suit to carry nitrogen (which comprises about 78% of Earth's atmosphere and is not used by the body). Lower pressure allows for greater mobility, but requires the suit occupant to breathe pure oxygen for a time before going into this lower pressure, to avoid decompression sickness.
- Mobility. Movement is typically opposed by the pressure of the suit; mobility is achieved by careful joint design. See the Theories of space suit design section.
- Supply of breathable oxygen and elimination of carbon dioxide; these gases are exchanged with the spacecraft or a Portable Life Support System (PLSS)
- Temperature regulation. Unlike on Earth, where heat can be transferred by convection to the atmosphere, in space, heat can be lost only by thermal radiation or by conduction to objects in physical contact with the exterior of the suit. Since the temperature on the outside of the suit varies greatly between sunlight and shadow, the suit is heavily insulated, and air temperature is maintained at a comfortable level.
- A communication system, with external electrical connection to the spacecraft or PLSS
- Means of collecting and containing solid and liquid bodily waste (such as a Maximum Absorbency Garment)
Advanced suits better regulate the astronaut's temperature with a Liquid Cooling and Ventilation Garment (LCVG) in contact with the astronaut's skin, from which the heat is dumped into space through an external radiator in the PLSS.
Additional requirements for EVA include:
- Shielding against ultraviolet radiation
- Limited shielding against particle radiation
- Means to maneuver, dock, release, and/or tether onto a spacecraft
- Protection against small micrometeoroids, some traveling at up to 27,000 kilometers per hour, provided by a puncture-resistant Thermal Micrometeoroid Garment, which is the outermost layer of the suit. Experience has shown the greatest chance of exposure occurs near the gravitational field of a moon or planet, so these were first employed on the Apollo lunar EVA suits (see United States suit models below).
As part of astronautical hygiene control (i.e., protecting astronauts from extremes of temperature, radiation, etc.), a space suit is essential for extravehicular activity. The Apollo/Skylab A7L suit included eleven layers in all: an inner liner, a LCVG, a pressure bladder, a restraint layer, another liner, and a Thermal Micrometeoroid Garment consisting of five aluminized insulation layers and an external layer of white Ortho-Fabric. This space suit is capable of protecting the astronaut from temperatures ranging from −156 °C (−249 °F) to 121 °C (250 °F).
During exploration of the Moon or Mars, there will be the potential for lunar/Martian dust to be retained on the space suit. When the space suit is removed on return to the spacecraft, there will be the potential for the dust to contaminate surfaces and increase the risks of inhalation and skin exposure. Astronautical hygienists are testing materials with reduced dust retention times and the potential to control the dust exposure risks during planetary exploration. Novel ingress/egress approaches, such as suitports, are being explored as well.
In NASA space suits, communications are provided via a cap worn over the head, which includes earphones and a microphone. Due to the coloration of the version used for Apollo and Skylab, which resembled the coloration of the comic strip character Snoopy, these caps became known as "Snoopy caps."
Generally, to supply enough oxygen for respiration, a space suit using pure oxygen must have a pressure of about 32.4 kPa (240 Torr; 4.7 psi), equal to the 20.7 kPa (160 Torr; 3.0 psi) partial pressure of oxygen in the Earth's atmosphere at sea level, plus 5.3 kPa (40 Torr; 0.77 psi) CO
2 and 6.3 kPa (47 Torr; 0.91 psi) water vapor pressure, both of which must be subtracted from the alveolar pressure to get alveolar oxygen partial pressure in 100% oxygen atmospheres, by the alveolar gas equation. The latter two figures add to 11.6 kPa (87 Torr; 1.7 psi), which is why many modern space suits do not use 20.7 kPa (160 Torr; 3.0 psi), but 32.4 kPa (240 Torr; 4.7 psi) (this is a slight overcorrection, as alveolar partial pressures at sea level are slightly less than the former). In space suits that use 20.7 kPa, the astronaut gets only 20.7 kPa − 11.6 kPa = 9.1 kPa (68 Torr; 1.3 psi) of oxygen, which is about the alveolar oxygen partial pressure attained at an altitude of 1,860 m (6,100 ft) above sea level. This is about 42% of normal partial pressure of oxygen at sea level, about the same as pressure in a commercial passenger jet aircraft, and is the realistic lower limit for safe ordinary space suit pressurization which allows reasonable capacity for work.
When space suits below a specific operating pressure are used from craft that are pressurized to normal atmospheric pressure (such as the Space Shuttle), this requires astronauts to "pre-breathe" (meaning pre-breathe pure oxygen for a period) before donning their suits and depressurizing in the air lock. This procedure purges the body of dissolved nitrogen, so as to avoid decompression sickness due to rapid depressurization from a nitrogen-containing atmosphere.
Physical effects of unprotected space exposure
This section needs additional citations for verification. (December 2014) (Learn how and when to remove this template message)
The human body can briefly survive the hard vacuum of space unprotected, despite contrary depictions in some popular science fiction. Human flesh expands to about twice its size in such conditions, giving the visual effect of a body builder rather than an overfilled balloon. Consciousness is retained for up to 15 seconds as the effects of oxygen starvation set in. No snap freeze effect occurs because all heat must be lost through thermal radiation or the evaporation of liquids, and the blood does not boil because it remains pressurized within the body.
In space, there are many different highly energized subatomic protons that will expose the body to extreme radiation. Although these compounds are minimal in amount, their high energy is liable to disrupt essential physical and chemical processes in the body, such as altering DNA or causing cancers. Exposure to radiation can create problems via two methods: the particles can react with water in the human body to produce free radicals that break DNA molecules apart, or by directly breaking the DNA molecules.
Temperature in space can vary extremely depending on where the sun is. Temperatures from solar radiation can reach up to 250 °F (121 °C) and lower down to −387 °F (−233 °C). Because of this, space suits must provide proper insulation and cooling.
The vacuum in space creates zero pressure, causing the gases and processes in the body to expand. In order to prevent chemical processes in the body from overreacting, it is necessary to develop a suit that counteracts against the pressure in space. The greatest danger is in attempting to hold one's breath before exposure, as the subsequent explosive decompression can damage the lungs. These effects have been confirmed through various accidents (including in very-high-altitude conditions, outer space and training vacuum chambers). Human skin does not need to be protected from vacuum and is gas-tight by itself. Instead, it only needs to be mechanically compressed to retain its normal shape. This can be accomplished with a tight-fitting elastic body suit and a helmet for containing breathing gases, known as a space activity suit (SAS).
This section possibly contains original research. (February 2012) (Learn how and when to remove this template message)
A space suit should allow its user natural unencumbered movement. Nearly all designs try to maintain a constant volume no matter what movements the wearer makes. This is because mechanical work is needed to change the volume of a constant pressure system. If flexing a joint reduces the volume of the space suit, then the astronaut must do extra work every time he bends that joint, and he has to maintain a force to keep the joint bent. Even if this force is very small, it can be seriously fatiguing to constantly fight against one's suit. It also makes delicate movements very difficult. The work required to bend a joint is dictated by the formula
where Vi and Vf are respectively the initial and final volume of the joint, P is the pressure in the suit, and W is the resultant work. It is generally true that all suits are more mobile at lower pressures. However, because a minimum internal pressure is dictated by life support requirements, the only means of further reducing work is to minimize the change in volume.
All space suit designs try to minimize or eliminate this problem. The most common solution is to form the suit out of multiple layers. The bladder layer is a rubbery, airtight layer much like a balloon. The restraint layer goes outside the bladder, and provides a specific shape for the suit. Since the bladder layer is larger than the restraint layer, the restraint takes all of the stresses caused by the pressure inside the suit. Since the bladder is not under pressure, it will not "pop" like a balloon, even if punctured. The restraint layer is shaped in such a way that bending a joint causes pockets of fabric, called "gores," to open up on the outside of the joint, while folds called "convolutes" fold up on the inside of the joint. The gores make up for the volume lost on the inside of the joint, and keep the suit at a nearly constant volume. However, once the gores are opened all the way, the joint cannot be bent any further without a considerable amount of work.
The outermost layer of a space suit, the Thermal Micrometeoroid Garment, provides thermal insulation, protection from micrometeoroids, and shielding from harmful solar radiation.
There are four main conceptual approaches to suit design:
Soft suits typically are made mostly of fabrics. All soft suits have some hard parts, some even have hard joint bearings. Intra-vehicular activity and early EVA suits were soft suits.
Hard-shell suits are usually made of metal or composite materials and do not use fabric for joints. Hard suits joints use ball bearings and wedge-ring segments similar to an adjustable elbow of a stove pipe to allow a wide range of movement with the arms and legs. The joints maintain a constant volume of air internally and do not have any counter force. Therefore, the astronaut does not need to exert to hold the suit in any position. Hard suits can also operate at higher pressures which would eliminate the need for an astronaut to pre-breathe oxygen to use a 34 kPa (4.9 psi) space suit before an EVA from a 101 kPa (14.6 psi) spacecraft cabin. The joints may get into a restricted or locked position requiring the astronaut to manipulate or program the joint. The NASA Ames Research Center experimental AX-5 hard-shell space suit had a flexibility rating of 95%. The wearer could move into 95% of the positions he or she could without the suit on.
Hybrid suits have hard-shell parts and fabric parts. NASA's Extravehicular Mobility Unit (EMU) uses a fiberglass Hard Upper Torso (HUT) and fabric limbs. ILC Dover's I-Suit replaces the HUT with a fabric soft upper torso to save weight, restricting the use of hard components to the joint bearings, helmet, waist seal, and rear entry hatch. Virtually all workable space suit designs incorporate hard components, particularly at interfaces such as the waist seal, bearings, and in the case of rear-entry suits, the back hatch, where all-soft alternatives are not viable.
Skintight suits, also known as mechanical counterpressure suits or space activity suits, are a proposed design which would use a heavy elastic body stocking to compress the body. The head is in a pressurized helmet, but the rest of the body is pressurized only by the elastic effect of the suit. This mitigates the constant volume problem, reduces the possibility of a space suit depressurization and gives a very lightweight suit. When not worn, the elastic garments may appear to be that of clothing for a small child. These suits may be very difficult to put on and face problems with providing a uniform pressure. Most proposals use the body's natural perspiration to keep cool. Sweat evaporates readily in vacuum and may desublime or deposit on objects nearby: optics, sensors, the astronaut's visor, and other surfaces. The icy film and sweat residue may contaminate sensitive surfaces and affect optical performance.
This section needs expansion. You can help by adding to it. (October 2010)
Related preceding technologies include the gas mask used in World War II, the oxygen mask used by pilots of high flying bombers in World War II, the high altitude or vacuum suit required by pilots of the Lockheed U-2 and SR-71 Blackbird, the diving suit, rebreather, scuba diving gear, and many others.
Many space suit designs are taken from the U.S. Air Force suits, which are designed to work in “high altitude aircraft pressure[s],” such as the Mercury IVA suit or the Gemini G4C, or the Advanced Crew Escape Suits.
The Mercury IVA, the first U.S. space suit design, included lights at the tips of the gloves in order to provide visual aid. As the need for extravehicular activity grew, suits such as the Apollo A7L included gloves made of a metal fabric called Chromel-r in order to prevent punctures. In order to retain a better sense of touch for the astronauts, the fingertips of the gloves were made of silicone. With the shuttle program, it became necessary to be able to operate spacecraft modules, so the ACES suits featured gripping on the gloves. EMU gloves, which are used for spacewalks, are heated to keep the astronaut's hands warm. The Phase VI gloves, meant for use with the Mark III suit, are the first gloves to be designed with "laser scanning technology, 3D computer modeling, stereo lithography, laser cutting technology and CNC machining." [NASA, ILC Dover Inc. 1] This allows for cheaper, more accurate production, as well as increased detail in joint mobility and flexibility.
Life support technology
Prior to the Apollo missions, life support in space suits was connected to the space capsule via an umbilical cord-like device. However, with the Apollo missions, life support was configured into a removable capsule called the Portable Life Support System that allowed the astronaut to explore the Moon without having to be attached to the space craft. The EMU space suit, used for spacewalks, allows the astronaut to manually control the internal environment of the suit. The Mark III suit has a backpack filled with about 12 pounds of liquid air, as well as pressurization and heat exchange.
The development of the spheroidal dome helmet was key in balancing the need for field of view, pressure compensation, and low weight. One inconvenience with some space suits is the head being fixed facing forwards and being unable to turn to look sideways. Astronauts call this effect "alligator head."
- Evgeniy Chertovsky created his full-pressure suit or high-altitude "skafandr" (скафандр) in 1931. (скафандр also means "diving apparatus").
- Emilio Herrera designed and built a full-pressure "stratonautical space suit" in 1935, which was to have been used during an open-basket balloon stratospheric flight scheduled for early 1936.
- Wiley Post experimented with a number of pressure suits for record-breaking flights.
- Russell Colley created the space suits worn by the Project Mercury astronauts, including fitting Alan Shepard for his ride as America's first man in space on May 5, 1961.
Models of historical significance
Soviet and Russian suit models
- SK series (CK), the spacesuit used for the Vostok program (1961–1963). Worn by Yuri Gagarin on the first crewed space flight.
- No pressure suits were worn aboard Voskhod 1.
- Berkut (Беркут = "golden eagle"), the spacesuit was a modified SK-1 used by the crew of Voskhod 2 which included Alexei Leonov on the first spacewalk during (1965).
- From Soyuz 1 to Soyuz 11 (1967–1971) no pressure suits were worn during launch and reentry.
- Yastreb (Ястреб = "hawk") extravehicular activity spacesuit used during a crew exchange between Soyuz 4 and Soyuz 5 (1969).
- Krechet-94 (Кречет = "gyrfalcon") spacesuit, designed for the canceled Soviet crewed Moon landing.
- Strizh (Стриж = "swift (bird)") spacesuit developed for pilots of Buran-class orbiters.
- Sokol (Сокол = "falcon") suits worn by Soyuz crew members during launch and reentry They were first worn on Soyuz 12. They have been used from 1973 to present.
- Orlan (Орлан = "sea-eagle" or "bald eagle") suits for extravehicular activity, originally developed for the Soviet lunar program as a lunar orbit EVA suit. It is Russia's current EVA suit. Used from 1977 to present.
Sokol-KV2 space suit
United States suit models
- In the early 1950s, Siegfried Hansen and colleagues at Litton Industries designed and built a working hard-shell suit, which was used inside vacuum chambers and was the predecessor of space suits used in NASA missions.
- Navy Mark IV high-altitude/vacuum suit used for Project Mercury (1961–1963).
- Gemini space suits (1965–1966), there were three main variants developed: G3C designed for intra-vehicle use; G4C specially designed for EVA and intra-vehicle use; and a special G5C suit worn by the Gemini 7 crew for 14 days inside the spacecraft.
- Manned Orbital Laboratory MH-7 space suits for the canceled MOL program.
- Apollo Block I A1C suit (1966–1967) was a derivative of the Gemini suit, worn by primary and backup crews in training for two early Apollo missions. The nylon pressure garment melted and burned through in the Apollo 1 cabin fire. This suit became obsolete when crewed Block I Apollo flights were discontinued after the fire.
- Apollo/Skylab A7L EVA and Moon suits. The Block II Apollo suit was the primary pressure suit worn for eleven Apollo flights, three Skylab flights, and the US astronauts on the Apollo–Soyuz Test Project between 1968 and 1975. The pressure garment's nylon outer layer was replaced with fireproof Beta cloth after the Apollo 1 fire. This suit was the first to employ a liquid-cooled inner garment and outer micrometeroid garment. Beginning with the Apollo 13 mission, it also introduced "commander's stripes" so that a pair of space walkers will not appear identical on camera.
- Shuttle Ejection Escape Suit used from STS-1 (1981) to STS-4 (1982) by a two-man crew used in conjunction with the then-installed ejection seats. Derived from a USAF model. These were removed once the Shuttle became certified.
- From STS-5 (1982) to STS-51-L (1986) no pressure suits were worn during launch and reentry. The crew would wear only a blue-flight suit with an oxygen helmet.
- Launch Entry Suit first used on STS-26 (1988), the first flight after the Challenger disaster. It was a partial pressure suit derived from a USAF model. It was used from 1988 to 1998.
- Advanced Crew Escape Suit used on the Space Shuttle starting in 1994. The Advanced Crew Escape Suit or ACES suit, is a full-pressure suit worn by all Space Shuttle crews for the ascent and entry portions of flight. The suit is a direct descendant of the United States Air Force high-altitude pressure suits worn by SR-71 Blackbird and U-2 spy plane pilots, North American X-15 and Gemini pilot-astronauts, and the Launch Entry Suits worn by NASA astronauts starting on the STS-26 flight. It is derived from a USAF model.
- Extravehicular Mobility Unit (EMU) used on both the Space Shuttle and International Space Station (ISS). The EMU is an independent anthropomorphic system that provides environmental protection, mobility, life support, and communications for a Space Shuttle or ISS crew member to perform an EVA in Earth orbit. Used from 1982 to present, but only available in limited sizing as of 2019.
- Orion Crew Survival System (OCSS) will be used during launch and re-entry on the Orion MPCV. It is derived from the Advanced Crew Escape Suit but is able to operate at a higher pressure and has improved mobility in the shoulders.
Chinese suit models
- Shuguang space suit. First generation EVA space suit developed by China for the 1967 canceled Project 714 crewed space program. With a mass of about 10 kilograms (20 lb), of orange colour, made of high-resistance multi-layers polyester fabric. The astronaut could use it inside the cabin and conduct an EVA as well.
- Project 863 space suit. Cancelled project of second generation Chinese EVA space suit.
- Shenzhou IVA (神舟) space suit. The suit was first worn by Yang Liwei on Shenzhou 5, the first crewed Chinese space flight, it closely resembles a Sokol-KV2 suit, but it is believed to be a Chinese-made version rather than an actual Russian suit. Pictures show that the suits on Shenzhou 6 differ in detail from the earlier suit, they are also reported to be lighter.
- Haiying (海鹰号航天服) EVA space suit. The imported Russian Orlan-M EVA suit is called Haiying. Used on Shenzhou 7.
- Feitian (飞天号航天服) EVA space suit. New generation indigenously developed Chinese-made EVA space suit also used for the Shenzhou 7 mission. The suit was designed for a spacewalk mission of up to seven hours. Chinese astronauts have been training in the out-of-capsule space suits since July 2007, and movements are seriously restricted in the suits, with a mass of more than 110 kilograms (240 lb) each.
This section's factual accuracy may be compromised due to out-of-date information. (April 2017)
Several companies and universities are developing technologies and prototypes which represent improvements over current space suits.
3D printing (additive manufacturing) can be used to reduce the mass of hard-shell space suits while retaining the high mobility they provide. This fabrication method also allows for the potential for in-situ fabrication and repair of suits, a capability which is not currently available, but will likely be necessary for Martian exploration. The University of Maryland began development of a prototype 3D printed hard suit in 2016, based on the kinematics of the AX-5. The prototype arm segment is designed to be evaluated in the Space Systems Laboratory glovebox to compare mobility to traditional soft suits. Initial research has focused on the feasibility of printing rigid suit elements, bearing races, ball bearings, seals, and sealing surfaces.
Astronaut Glove Challenge
There are certain difficulties in designing a dexterous space suit glove and there are limitations to the current designs. For this reason, the Centennial Astronaut Glove Challenge was created to build a better glove. Competitions have been held in 2007 and 2009, and another is planned. The 2009 contest required the glove to be covered with a micro-meteorite layer.
Since 2009, the Austrian Space Forum has been developing "Aouda.X", an experimental Mars analogue space suit focusing on an advanced human-machine interface and on-board computing network to increase situational awareness. The suit is designed to study contamination vectors in planetary exploration analogue environments and create limitations depending on the pressure regime chosen for a simulation.
Since 2012, for the Mars2013 analogue mission by the Austrian Space Forum to Erfoud, Morocco, the Aouda.X analogue space suit has a sister in the form of Aouda.S. This is a slightly less sophisticated suit meant primarily to assist Aouda.X operations and be able to study the interactions between two (analogue) astronauts in similar suits.
The Aouda.X and Aouda.S space suits have been named after the fictional princess from the Jules Verne's 1873 novel Around the World in Eighty Days and can be followed on Facebook. A public display mock-up of Aouda.X (called Aouda.D) is currently on display at the Dachstein Ice Cave in Obertraun, Austria, after the experiments done there in 2012.
Bio-Suit is a space activity suit under development at the Massachusetts Institute of Technology, which as of 2006[update] consisted of several lower leg prototypes. Bio-suit is custom fit to each wearer, using laser body scanning.[needs update]
Constellation Space Suit system
On August 2, 2006, NASA indicated plans to issue a Request for Proposal (RFP) for the design, development, certification, production, and sustaining engineering of the Constellation Space Suit to meet the needs of the Constellation Program. NASA foresaw a single suit capable of supporting: survivability during launch, entry and abort; zero-gravity EVA; lunar surface EVA; and Mars surface EVA.
Final Frontier Design IVA Space Suit
Final Frontier Design (FFD) is developing a commercial full IVA space suit, with their first suit completed in 2010. FFD's suits are intended as a light-weight, highly mobile, and inexpensive commercial space suits. Since 2011, FFD has upgraded IVA suit's designs, hardware, processes, and capabilities. FFD has built a total of 7 IVA space suit (2016) assemblies for various institutions and customers since founding, and has conducted high fidelity human testing in simulators, aircraft, microgravity, and hypobaric chambers. FFD has a Space Act Agreement with NASA's Commercial Space Capabilities Office to develop and execute a Human Rating Plan for FFD IVA suit. FFD categorizes their IVA suits according to their mission: Terra for Earth-based testing, Stratos for high altitude flights, and Exos for orbital space flights. Each suit category has different requirements for manufacturing controls, validations, and materials, but are of a similar architecture.
The I-Suit is a space suit prototype also constructed by ILC Dover, which incorporates several design improvements over the EMU, including a weight-saving soft upper torso. Both the Mark III and the I-Suit have taken part in NASA's annual Desert Research and Technology Studies (D-RATS) field trials, during which suit occupants interact with one another, and with rovers and other equipment.
The Mark III is a NASA prototype, constructed by ILC Dover, which incorporates a hard lower torso section and a mix of soft and hard components. The Mark III is markedly more mobile than previous suits, despite its high operating pressure (57 kPa or 8.3 psi), which makes it a "zero-prebreathe" suit, meaning that astronauts would be able to transition directly from a one atmosphere, mixed-gas space station environment, such as that on the International Space Station, to the suit, without risking decompression sickness, which can occur with rapid depressurization from an atmosphere containing nitrogen or another inert gas.
The MX-2 is a space suit analogue constructed at the University of Maryland's Space Systems Laboratory. The MX-2 is used[when?] for crewed neutral buoyancy testing at the Space Systems Lab's Neutral Buoyancy Research Facility. By approximating the work envelope of a real EVA suit, without meeting the requirements of a flight-rated suit, the MX-2 provides an inexpensive platform for EVA research, compared to using EMU suits at facilities like NASA's Neutral Buoyancy Laboratory.
The MX-2 has an operating pressure of 2.5–4 psi. It is a rear-entry suit, featuring a fiberglass HUT. Air, LCVG cooling water, and power are open loop systems, provided through an umbilical. The suit contains a Mac mini computer to capture sensor data, such as suit pressure, inlet and outlet air temperatures, and heart rate. Resizable suit elements and adjustable ballast allow the suit to accommodate subjects ranging in height from 68 to 75 inches (170–190 cm), and with a weight range of 120 lb (54 kg).
North Dakota suit
Beginning in May 2006, five North Dakota colleges collaborated on a new space suit prototype, funded by a US$100,000 grant from NASA, to demonstrate technologies which could be incorporated into a planetary suit. The suit was tested in the Theodore Roosevelt National Park badlands of western North Dakota. The suit has a mass of 47 pounds (21 kg) without a life support backpack, and costs only a fraction of the standard US$12,000,000 cost for a flight-rated NASA space suit. The suit was developed in just over a year by students from the University of North Dakota, North Dakota State, Dickinson State, the state College of Science and Turtle Mountain Community College. The mobility of the North Dakota suit can be attributed to its low operating pressure; while the North Dakota suit was field tested at a pressure of 1 psi (6.9 kPa; 52 Torr) differential, NASA's EMU suit operates at a pressure of 4.7 psi (32 kPa; 240 Torr), a pressure designed to supply approximately sea-level oxygen partial pressure for respiration (see discussion above).
NASA's Prototype eXploration Suit (PXS), like the Z-series, is a rear-entry suit compatible with suitports. The suit has components which could be 3D printed during missions to a range of specifications, to fit different individuals or changing mobility requirements.
SpaceX suit ("Starman suit")
In February 2015, SpaceX began developing a space suit for astronauts to wear within the Dragon 2 space capsule. Its appearance was jointly designed by Jose Fernandez—a Hollywood costume designer known for his works for superhero and science fiction films—and SpaceX founder and CEO Elon Musk. The first images of the suit were revealed in September 2017. A mannequin, called "Starman" (after David Bowie's song of the same name), wore the SpaceX space suit during the maiden launch of the Falcon Heavy in February 2018. For this exhibition launch, the suit was not pressurized and carried no sensors.
The suit, which is suitable for vacuum, offers protection against cabin depressurization through a single tether at the astronaut's thigh that feeds air and electronic connections. The helmets, which are 3D-printed, contain microphones and speakers. As the suits need the tether connection and do not offer protection against radiation, they are not used for extra-vehicular activities.
In 2018, NASA commercial crew astronauts Bob Behnken, and Doug Hurley tested the spacesuit inside the Dragon 2 spacecraft in order to familiarize themselves with the suit. They wore it in the Crew Dragon Demo-2 flight launched on 30 May 2020. The suit is worn by astronauts involved in Commercial Crew Program missions involving SpaceX.
A suitport is a theoretical alternative to an airlock, designed for use in hazardous environments and in human spaceflight, especially planetary surface exploration. In a suitport system, a rear-entry space suit is attached and sealed against the outside of a spacecraft, such that an astronaut can enter and seal up the suit, then go on EVA, without the need for an airlock or depressurizing the spacecraft cabin. Suitports require less mass and volume than airlocks, provide dust mitigation, and prevent cross-contamination of the inside and outside environments. Patents for suitport designs were filed in 1996 by Philip Culbertson Jr. of NASA's Ames Research Center and in 2003 by Joerg Boettcher, Stephen Ransom, and Frank Steinsiek.
In 2012, NASA introduced the Z-1 space suit, the first in the Z-series of space suit prototypes designed by NASA specifically for planetary extravehicular activity. The Z-1 space suit includes an emphasis on mobility and protection for space missions. It features a soft torso versus the hard torsos seen in previous NASA EVA space suits, which provides reduced mass. It has been labeled the "Buzz Lightyear suit" due to its green streaks for a design.
In 2014, NASA released the design for the Z-2 prototype, the next model in the Z-series. NASA conducted a poll asking the public to decide on a design for the Z-2 space suit. The designs, created by fashion students from Philadelphia University, were "Technology", "Trends in Society", and "Biomimicry." The design "Technology" won, and the prototype is built with technologies like 3D printing. The Z-2 suit will also differ from the Z-1 suit in that the torso reverts to the hard shell, as seen in NASA's EMU suit.
The earliest space fiction ignored the problems of traveling through a vacuum, and launched its heroes through space without any special protection. In the later 19th century, however, a more realistic brand of space fiction emerged, in which authors have tried to describe or depict the space suits worn by their characters. These fictional suits vary in appearance and technology, and range from the highly authentic to the utterly improbable.
A very early fictional account of space suits can be seen in Garrett P. Serviss' novel Edison's Conquest of Mars (1898). Later comic book series such as Buck Rogers (1930s) and Dan Dare (1950s) also featured their own takes on space suit design. Science fiction authors such as Robert A. Heinlein contributed to the development of fictional space suit concepts.
- Atmospheric diving suit
- Effect of spaceflight on the human body – Medical consequences of spaceflight
- Extravehicular activity – Activity done by an astronaut or cosmonaut outside a spacecraft – lists:
- By era:
- By station:
- List of cumulative spacewalk records – Wikipedia list article
- Manned Maneuvering Unit
- Thomas, Kenneth S.; McMann, Harold J. (November 23, 2011). U.S. Spacesuits. Springer Science & Business Media.
- Martin, Lawrence. "The Four Most Important Equations In Clinical Practice". GlobalRPh. David McAuley. Retrieved June 19, 2013.
- Bellows, Alan (November 27, 2006). "Outer Space Exposure". Damn Interesting. Article #237. Retrieved June 19, 2013.
- "Space Radiation Analysis Group". NASA, Johnson Space Center. NASA. Archived from the original on February 18, 2015. Retrieved February 16, 2015.
- Hanslmeier, Arnold (January 1, 2002). The Sun and Space Weather (Illustrated ed.). Springer Science & Business Media. pp. 166–67. ISBN 1402006845.
- "Ask an Astrophysicist: Human Body in a Vacuum". Image the Universe!. NASA. Retrieved December 14, 2008.
- "NASA Spacesuits". NASA. NASA. Archived from the original on May 20, 2010. Retrieved February 17, 2015.
- "Escafandra Estratonautica". Encyclopedia Astronautica. Mark Wade. Archived from the original on May 22, 2013. Retrieved June 19, 2013.
- "Siegfried Hansen, Space Suit Father; Inventor Was 90". The New York Times. July 24, 2002. Retrieved February 9, 2008.
- Jones, Eric (February 20, 2006). "Commander's Stripes". Apollo Lunar Surface Journal. NASA. Retrieved April 7, 2019.
- Thomas & McMann 2006, pp. 38, 368
- Thomas & McMann 2006
- "ACES". Encyclopedia Astronautica. Mark Wade. Archived from the original on May 30, 2013. Retrieved June 19, 2013.
- Koren, Marina. "The Original Sin of NASA Space Suits". TheAtlantic.com. The Atlantic Monthly Group. Retrieved March 29, 2019.
In the 1990s, several years after the first American women flew to space, budget cuts forced NASA to trim its space-suit program...The limited sizing affected some astronaut duties.
- Shane E. Jacobs; Donald B. Tufts; Dustin M. Gohmert (July 8–12, 2018). "Space Suit Development for Orion" (PDF). 48th International Conference on Environmental Systems. Albuquerque, New Mexico. Retrieved July 6, 2019.
- "为中华航天史册再添辉煌". 国防科工委新闻宣传中心. November 14, 2005. Retrieved July 22, 2008.[dead link]
- "航天服充压实验". 雷霆万钧. September 19, 2005. Archived from the original on December 22, 2005. Retrieved July 24, 2008.
- "中国最早研制的航天服为桔黄色 重10千克". 雷霆万钧. September 16, 2005. Archived from the original on November 28, 2005. Retrieved July 24, 2008.
- "舱外航天服液冷服散热特性研究". 北京航���航天大学图书馆. March 1, 2000. Retrieved July 23, 2008.[dead link]
- "Testimony of James Oberg: Senate Science, Technology, and Space Hearing: International Space Exploration Program". SpaceRef. Reston, VA: SpaceRef Interactive Inc. April 27, 2004. Retrieved April 12, 2011.
- Seedhouse 2010, p. 180
- Malik, Tariq (November 8, 2004). "China Ramps Up Human Spaceflight Efforts". Space.com. TechMediaNetwork, Inc. Retrieved June 19, 2013.
- "神七准备中俄产两套航天服 出舱者穿国产航天服". 搜狐. July 22, 2008. Retrieved July 22, 2008.[dead link]
- Xiao Jie, ed. (June 1, 2007). "China's astronaut outfitters design material for spacewalk suits". English.news.cn. Beijing: Xinhua News Agency. Archived from the original on January 25, 2008. Retrieved June 1, 2007.
- "Chinese astronauts begin training for spacewalk". People's Daily Online. Beijing: Central Committee of the Communist Party of China. Xinhua News Agency. July 18, 2007. Retrieved August 1, 2007.
- Bartlett, Harrison; Bowser, Joseph; Callejon Hierro, Carlos; Garner, Sarah; Guloy, Lawrence; Hnatov, Christina; Kalman, Jonathan; Sosis, Baram; Akin, David (July 16, 2017). In-Situ Fabricated Space Suits for Extended Exploration and Settlement. 2017 International Conference on Environmental Systems. Charleston, SC. Retrieved December 11, 2018.
- Garner, Sarah; Carpenter, Lemuel; Akin, David (July 8, 2018). Developing Technologies and Techniques for Additive Manufacturing of Spacesuit Bearings and Seals. 2018 International Conference on Environmental Systems. Albuquerque, NM. Retrieved December 11, 2018.
- "Spacesuit-simulator 'Aouda.X'". PolAres. Austrian Space Forum. Archived from the original on May 29, 2013. Retrieved June 19, 2013.
- "Morocco 2013 Mars Analogue Field Simulation". PolAres. Austrian Space Forum. Retrieved June 19, 2013.
- "Mars 2013 - Morocco Mars Analog Field Simulation" (Press release). Austrian Space Forum. Archived from the original on June 24, 2013. Retrieved June 19, 2013.
- Austrian Space Forum on Facebook
- "Aouda.D, ice princess". PolAres (Blog). Austrian Space Forum. Retrieved June 19, 2013.
- "CONSTELLATION SPACE SUIT SYSTEM (CSSS), SOL NNJ06161022R". NASA Acquisition Internet Service. NASA. Archived from the original on July 30, 2009. Retrieved June 19, 2013.
- "Get your first look at NASA's next spacesuit". NBCNews.com. Associated Press. June 12, 2008. Retrieved June 19, 2013.
- "Inventors to Unveil Private Spacesuit in New York". July 16, 2010. Retrieved July 17, 2010.
- "NASA Selects Commercial Space Partners for Collaborative Partnerships". December 23, 2014. Retrieved December 24, 2010.
- "MARS Suit: MX-2". Space Systems Laboratory. College Park, MD: University of Maryland. Archived from the original on September 3, 2012. Retrieved June 19, 2013.
- Jacobs, Shane E.; Akin, David L.; Braden, Jeffrey R. (July 17, 2006). System Overview and Operations of the MX-2 Neutral Buoyancy Space Suit Analogue. International Conference On Environmental Systems. SAE International. doi:10.4271/2006-01-2287. 2006-01-2287. Retrieved June 12, 2007.
- Freudenrich, Craig. "How Space Suits Work". HowStuffWorks. Atlanta, GA: Discovery Communications. Retrieved June 19, 2013.
- MacPherson, James (May 7, 2006). "That's one small step toward Mars mission". The San Diego Union-Tribune. Associated Press. Retrieved June 19, 2013.
- Howell, Elizabeth (August 25, 2015). "'The Martian' Shows 9 Ways NASA Tech Is Headed to Mars". space.com. Retrieved December 18, 2015.
- "The Next Generation of Suit Technologies". NASA. October 1, 2015. Archived from the original on December 15, 2015. Retrieved December 18, 2015.
Reisman, Garrett (February 27, 2015). "Statement of Garrett Reisman before the Subcommittee on Space Committee on Science, Space, and Technology U.S. House Of Representatives" (PDF). http://science.house.gov. US House of Representatives publication of a SpaceX document provided to the committee. Retrieved February 28, 2015.
Crew Dragon carries sufficient breathable gas stores to allow for a safe return to Earth in the event of a leak of up to an equivalent orifice of 0.25 inches in diameter. As an extra level of protection, the crew will wear SpaceX-designed space suits to protect them from a rapid cabin depressurization emergency event of even greater severity. The suits and the vehicle itself will be rated for operation at vacuum.External link in
- Martin, Guy. "The Man Behind America's New Spacesuit: How Elon Musk Took Hollywood Costume Designer Jose Fernandez From Batman To NASA". Forbes. Retrieved June 3, 2020.
- Bobb, Brooke. "SpaceX's New Suits Were Built for Superheroes, But What Would Wonder Woman Wear into Orbit?". Vogue. Retrieved June 3, 2020.
- Etherington, Darrell (September 8, 2017). "Elon Musk shares first full-body photo of SpaceX's spacesuit". Tech Crunch. Retrieved February 6, 2018.
- Seemangal, Robin (February 6, 2018). "SPACEX SUCCESSFULLY LAUNCHES THE FALCON HEAVY—AND ELON MUSK'S ROADSTER". Wired. Retrieved February 6, 2018.
- Brandon Specktor 08 February 2018. "Starman's SpaceX Spacesuit Would Leave You Dead in Minutes". livescience.com. Retrieved June 3, 2020.
- SpaceX Just Launched a Tesla Into Space on the Most Powerful Rocket in the World. Motherboard. 6 February 2018. Quote:"Musk said at a press conference after the launch that there were no sensors in the suit."
- May 2020, Elizabeth Howell 22. "How SpaceX's sleek spacesuit changes astronaut fashion from the space shuttle era". Space.com. Retrieved June 3, 2020.
- Kooser, Amanda (November 6, 2018). "NASA astronauts test SpaceX spacesuits in the Crew Dragon". cnet.com. Retrieved November 9, 2018.
- Culbertson, Philip, Jr. (September 30, 1996). "Suitlock docking mechanism – United States Patent 5697108". freepatentsonline.com. Retrieved June 15, 2006.
- Boettcher, Joerg; Ransom, Stephen; Steinsiek, Frank (July 17, 2003). "Apparatus and method for putting on a protective suit – United States Patent 6959456". freepatentsonline.com. Retrieved June 15, 2006.
- TIME Staff. "NASA's Z-1 Space Suit". TIME. TIME Magazine. Archived from the original on February 20, 2015. Retrieved February 17, 2015.
- Kirkpatrick, Nick. "Intergalactic fashion: NASA's next space suit". Washington Post. Washington Post. Retrieved February 17, 2015.
- CBC News (May 1, 2014). "New Mars space suit unveiled by NASA". CBC/Radio-Canada. Retrieved February 17, 2015.
- "The NASA Z-2 Suit". NASA.gov. NASA. Archived from the original on March 29, 2014.
- Graziosi, David; Stein, James; Ross, Amy; Kosmo, Joseph (January 21, 2011). "Phase VI Advanced EVA Glove Development and Certification for the International Space Station". Cite journal requires
- Abramov, Isaac P.; Skoog, Å. Ingemar; et al. (2003). Russian Spacesuits. London; New York: Springer-Verlag. ISBN 1-85233-732-X. LCCN 2003045585. OCLC 51922847.
- de Monchaux, Nicholas (2011). Spacesuit: Fashioning Apollo. MIT Press. ISBN 978-0262015202.
- Kozloski, Lillian D. (1994). U.S. Space Gear: Outfitting The Astronaut. Washington, D.C.: Smithsonian Institution Press. ISBN 0-87474-459-8. LCCN 92-34611. OCLC 623508754.
- Seedhouse, Erik (2010). The New Space Race: China vs. the United States. Berlin; New York: Springer. ISBN 978-1-4419-0879-7. LCCN 2009936076. OCLC 695700526.
- Thomas, Kenneth S.; McMann, Harold J. (2006). US Spacesuits. Berlin; New York: Springer-Verlag. ISBN 0-387-27919-9. LCCN 2005929632. OCLC 61477760.
- Young, Amanda (2009). Spacesuits: The Smithsonian National Air and Space Museum Collection. Photographs by Mark Avino; introduction by Allan Needell; foreword by Thomas P. Stafford (1st ed.). Brooklyn, NY: powerHouse Books. ISBN 978-1-576-87498-1. LCCN 2009075080. OCLC 276334393.
|Wikimedia Commons has media related to Space suits.|
- "Space suits" at A Field Guide to American Spacecraft. A list compiled by Lee Sledge and James H. Gerard of American space suits and the museum locations where they are displayed.
- "Space Suits" at Encyclopedia Astronautica. A complete listing of space suits.
- Russian space suits at NPP Zvezda
- "Space suit" (in Russian) English by G. Ilyin, Vladimir Ivanov, and Ivan Pavlov. Originally published by Nauka i Zhizn, No. 6, 1978.
- "U.S. Human Spaceflight History" at the Johnson Space Center See link near page end to Walking to Olympus: An EVA Chronology (PDF).
- NASDA Online Space Notes at the National Space Development Agency of Japan (NASDA) (2001)
- "Analysis of the Space Shuttle Extravehicular Mobility Unit – 1986" (PDF)
- "NASA Space Shuttle EVA tools and equipment reference book – 1993" (PDF)
- "Space Suit Evolution From Custom Tailored to Off-the-Rack (PDF)
- "Engineering Aspects of Apollo" at the Apollo Lunar Surface Journal. Section on the Apollo space suit and the Portable Life Support System.
- "Space Suit Photos" at Historic Spacecraft
- "Space suit and Spacewalk History Image Gallery" at NASA
- Zvezda history (in Russian) English
- "EVA Space Suits (Extravehicular Activity)" at ILC Dover
- Klesius, Michael (June 10, 2009). "Space Suits Past and Future". AirSpaceMag.com. Washington, D.C.: Smithsonian Institution. Retrieved June 20, 2013.
- In April 2011, the VOA Special English service of the Voice of America broadcast a 15-minute program on the evolution of space suits. A transcript and MP3 of the program, intended for English learners, can be found at "The Evolution of Spacesuits".