This article is missing information about the version history (table).August 2019)(
The Qi logo, consisting of a lowercase "q" with a semicircle-esque "i" with a circle on top, which when put together resemble an uppercase "Q".
January 28, 2018
|Organization||Wireless Power Consortium|
|Committee||Wireless Power Consortium|
|Related standards||Cordless Kitchen standard|
Medium Power standard
|Copyright||Logo and trademark|
Qi (pronounced // CHEE; from the Chinese word qi) is an open interface standard that defines wireless power transfer using inductive charging over distances of up to 4 cm (1.6 inches), developed by the Wireless Power Consortium. The system uses a charging pad and a compatible device, which is placed on top of the pad, charging via resonant inductive coupling.
First released in 2008, the Qi standard had by 2019 been incorporated into more than 160 smartphones, tablets and other devices.
This section needs expansion. You can help by adding to it. (August 2019)
|Version number||Released||Maximum wattage||Notes|
|1.2||2015||Baseline Power Profile (BPP): 5W
Extended Power Profile (EPP): 15 W
|Labeled by Samsung as “Fast Wireless Charging” (initially 10W, introduced on the Galaxy Note 5 and S6 edge plus), August 2015) requires charging plate to be connected to Qualcomm Quick Charge 2.0-enabled 15W USB charger (9 Volt, 1.67 Ampère support).|
Features and specifications
The WPC published the Qi low-power specification in August 2009. The Qi specification can be downloaded freely after registration. Under the Qi specification, "low power" inductive transfers deliver power below 5 W using inductive coupling between two planar coils. These coils are typically 5 mm apart but can be up to 40 mm and possibly farther apart. The Qi low-power specification has been renamed to the Qi Baseline Power Profile (BPP).
Regulation of the output voltage is provided by a digital control loop where the power receiver communicates with the power transmitter and requests more or less power. Communication is unidirectional from the power receiver to the power transmitter via backscatter modulation. In backscatter modulation, the power-receiver coil is loaded, changing the current draw at the power transmitter. These current changes are monitored and demodulated into the information required for the two devices to work together.
In 2011, the Wireless Power Consortium began to extend the Qi specification to medium power. As of 2019, the Medium Power standard currently delivers 30 to 65 W, it is expected to eventually support up to 200 W (typically used for portable power tools, robotic vacuum cleaners, drones and e-bikes).
In 2015, the WPC also demonstrated a high-power specification that will deliver up to 1 kW, allowing the powering of kitchen appliances among other high-power utilities.
Extended Power Profile (EPP)
In 2015, WPC introduced the Qi Extended Power Profile (EPP) specification which supports up to 15 W. EPP is also typically used to charge mobile devices like BPP.
Proprietary Power Delivery Extension (PDDE)
WPC introduced Proprietary Power Delivery Extension (PDDE) to allow phone OEMs to deliver higher than Baseline Power Profile's 5W or the Extended Power Profile's 15W. Currently only Samsung has published their compliance test. Other phone companies that use proprietary standards for fast wireless charging include Apple, Huawei and Google.
Nokia first adopted Qi in its Lumia 920, and Samsung Mobile on the Galaxy S3 (supportable via retrofittable official Samsung back cover accessory) in 2012,, the Google/LG Nexus 4 followed later that year. Toyota began offering a Qi charging cradle as a factory option on its 2013 Avalon Limited, with Ssangyong the second car manufacturer to offer a Qi option, also in 2013.
In 2015, a survey found that 76% of people surveyed in the United States, United Kingdom, and China were aware of wireless charging (an increase from 36% the previous year), and 20% were using it — however only 16% of those using it were using it daily. Furniture retailer IKEA introduced lamps and tables with integrated wireless chargers for sale in 2015, and the Lexus NX gained an optional Qi charging pad in the center console. An estimated 120 million wirelessly charging phones were sold that year, notably the Samsung Galaxy S6, which supported both Qi and the competing Power Matters Alliance standards. However, the existence of several competing wireless charging standards was still seen as a barrier to adoption.
By early 2017, Qi had displaced the competing standards, with no new products featuring Rezence. On September 12, 2017, Apple Inc. announced that their new smartphones, the iPhone 8, iPhone 8 Plus, and the iPhone X, will support the Qi standard. Since then, every new iPhone version has supported the Qi wireless charging standard. Apple also announced plans to expand the standard with a new protocol called AirPower which would have added the ability to charge multiple devices at once; however, this was canceled on March 29, 2019.
As the Qi standard gains popularity, it is expected that Qi Hotspots will begin to arise in places such as coffee shops, airports, sports arenas, etc. The Coffee Bean and Tea Leaf, a major US coffee chain, will install inductive charging stations at selected major metropolitan cities, as well as Virgin Atlantic Airways, for United Kingdom's London Heathrow Airport and New York City's John F. Kennedy International Airport. Automobile manufacturers have been adding QI charging as standard or optional features since 2013.
Devices that operate with the Qi standard rely on electromagnetic induction between planar coils. A Qi system consists of two types of devices – the Base Station, which is connected to a power source and provides inductive power, and Mobile Devices, which consume inductive power. The Base Station contains a power transmitter that comprises a transmitting coil that generates an oscillating magnetic field; the Mobile Device contains a power receiver holding a receiving coil. The magnetic field induces an alternating current in the receiving coil by Faraday's law of induction. Close spacing of the two coils, as well as shielding on their surfaces, ensure the inductive power transfer is efficient.
Base Stations typically have a flat surface—referred to as the Interface Surface—on top of which a user can place one or more Mobile Devices. There are two methods for aligning the transmitting coil (part of the Base Station) and receiving coil (part of the Mobile Device) in order for a power transfer to happen. In the first concept—called guided positioning—a user must place the Mobile Device on a certain location of the Base Station's surface. For this purpose, the Mobile Device provides an alignment aid that is appropriate to its size, shape and function. The second concept—referred to as free positioning—does not require the user to place the Mobile Device in direct alignment with the transmitting coil. There are several ways to achieve free positioning. In one example a bundle of transmitting coils is used to generate a magnetic field at the location of the receiving coil only. Another example uses mechanical means to move a single transmitting coil underneath the receiving coil. A third option is to use a technique called "Multiple Cooperative Flux Generators."
Figure 1-1 illustrates the basic system configuration. As shown, a power transmitter includes two main functional units—a power conversion unit and a communications and control unit. The diagram shows the transmitting coil (array) generating the magnetic field as part of the power conversion unit. The control and communications unit regulates the transferred power to the level that the power receiver requests. The diagram also demonstrates that a Base Station may contain numerous transmitters, allowing for multiple Mobile Devices to be placed on the same Base Station and inductively charge until each of its batteries are fully charged. Finally, the system unit in the diagram comprises all other functionality of the Base Station, such as input power provisioning, control of multiple power transmitters, and user interfacing.
A power receiver comprises a power pick-up unit, as well as a communications and control unit. Similar to the power conversion unit of the transmitter, Figure 1-1 illustrates the receiving coil as capturing the magnetic field of the power pick-up unit. A power pick-up unit typically contains a single receiving coil only. Moreover, a Mobile Device typically contains a single power receiver. The communications and control unit regulates the transferred power to the level that is appropriate for the subsystems (e.g., battery) connected to the output of the power receiver. These subsystems represent the main functionality of the Mobile Device.
Example power transmitter hardware
As an example from the 2017 version 1.2.2 of the Qi specification (referenced above), the A2 reference Qi low-power transmitter has a coil of 20 turns (in two layers) in a flat coil, wound on a form with a 19mm inner diameter and a 40mm outer diameter, with a below-coil shield of soft iron at least 4mm larger in diameter which gives an inductance of 24 +-1 microhenries. This coil is placed in a series resonant circuit with a 200 nF capacitor to yield a resonant circuit with a natural resonance at ~140 kHz when coupled to the receiver coil.
This series resonant circuit is then driven by an H-bridge switching arrangement from the DC source; at full power, the voltage in the capacitor can reach 50 volts. Power control is automatic; the Qi specification requires that the actual voltage applied be controllable in steps at least as small as 50 millivolts.
Rather than down-regulate the charging voltage in the device, Qi chargers meeting the A2 reference use a PID (proportional-integral-derivative) controller to modulate the delivered power according to the primary cell voltage.
Other Qi charge transmitters start their connections at 140 kHz, but can change frequencies to find a frequency with a better match, as the mutual inductance between transmitter and receiver coils will vary according to the standoff distance between transmitter and receiver coils, and thus the natural resonance frequency will vary. Different Qi reference designs have different coil arrangements, including oval coil and multi-coil systems as well as more complex resonance networks with multiple inductors and capacitors. These designs allow frequency-agile operation at frequencies from 105 to 205 kHz and with maximum resonant circuit voltages as high as 200 volts.
Example power receiver hardware
The Qi power receiver hardware reference design 1, also from version 1.2.2 of the Qi specification, starts with a rectangular coil of wire 44 mm x 30 mm outside size, with 14 turns of wire, and with an above-coil magnetic shield. This coil is wired into a parallel resonant circuit with a pair of capacitors (of 127 nanofarads and 1.6 nanofarads in series). The power output is taken across the 1.6 nanofarad capacitor.
In order to provide a digital communications channel back to the power transmitter, a resonance modulator consisting of a pair of 22 nanofarad capacitors and a 10 kΩ resistor in a T configuration can be switched across the 1.6 nanofarad capacitor. Switching the T network across the 1.6 nanofarad capacitor causes a significant change in the resonant frequency of the coupled system that is detected by the power transmitter as a change in the delivered power.
Power output to the portable device is via a full-wave bridge wired across the 1.6 nanofarad capacitor; the power is typically filtered with a 20 microfarad capacitor before delivery to the charge controller.
Other Qi power receivers use alternate resonance modulators, including switching a resistor or pair of resistors across the receiver resonator capacitor, both before and after the bridge rectifier.
- Wireless power transfer
- Inductive coupling
- Resonant inductive coupling
- Near field communication
- Rezence, a competing wireless power standard promoted by The Alliance for Wireless Power and the Power Matters Alliance
- WiPower, a formerly competing wireless power standard promoted by The Alliance For Wireless Power that merged with PMA to form Rezence
- PMA, a formerly competing wireless power standard promoted by the Power Matters Alliance that merged with WiPower to form Rezence
- Open Dots, a competing wireless power standard promoted by the Open Dots Alliance
- "Wireless Power Consortium". Retrieved November 22, 2015.
- "eCoupled Wireless Power Through Granite". YouTube. Google.
- "An introduction to the Wireless Power Consortium standard and TI's compliant solutions" (PDF). Ti. Archived from the original on 2015-05-29.CS1 maint: BOT: original-url status unknown (link)
- "Members". Wireless Power Consortium.
- "Qi enabled Phones / Qi compatible Devices". Qi Wireless Charging. Retrieved September 27, 2017.
- "History of the Qi specification". Wireless Power Consortium. Retrieved 2019-09-05.
- "The Wireless Power Consortium Releases the 0.95 Specification". Electronic Component News. 2009-09-11. Retrieved 2017-09-27.
- "Download Wireless Power Specification Part 1". Wireless Power Consortium. Archived from the original on April 3, 2016. Retrieved February 2, 2018.
- "Medium power extension". Archived from the original on 11 March 2012.
- "Medium Power Standard". Wireless Power Consortium. Retrieved 2019-09-02.
- "LG AND IDT PARTNER ON WORLD'S FIRST Qi EXTENDED POWER PROFILE SMARTPHONE". LG Newsroom. 2017-11-07. Retrieved 2019-09-03.
- Inc, Integrated Device Technology. "Sony Mobile Selects IDT Wireless Charging Chipset for XZ2 Smartphones and Wireless Charging Dock Solution". www.prnewswire.com. Retrieved 2019-09-03.
- Floyd. "Interviewing WPC Chairman Menno Treffers: the Future is Wireless – Chargerlab". Retrieved 2019-09-03.
- "AQUOS R3のユーザビリティ｜AQUOS：シャープ". シャープ スマートフォン・携帯電話 AQUOS公式サイト (in Japanese). Retrieved 2019-09-03.
- "Safety of Proprietary Extensions". Wireless Power Consortium. Retrieved 2019-09-03.
- Wired, Qi Wireless Charging: What Is It And How Does It Work In Nokia's Lumia 920?, 5 September 2012
- The Verge, Toyota's 2013 Avalon Limited becomes world's first car to adopt Qi wireless charging, 19 December 2012
- Torque News, Qi wireless charging system adopted by second automaker for use in cars, 25 February 2013
- IHS Markit, Consumer Awareness of Wireless Charging Doubles to 76 Percent in 2015, IHS Says, 24 June 2015
- Brian, Matt. "IKEA will start selling wireless charging lamps and tables". Engadget. Retrieved 1 March 2015.
- "Wireless Charger - Unbound Convenience". www.lexus.com. Archived from the original on 2015-02-09. Retrieved 2017-08-07.
- Wired, Wireless Charging Is Still a Mess, But It Won’t Be Forever, 12 November 2015
- E&T, Qi wireless charging standard emerges victorious; adoption rapidly increasing, 17 February 2017
- "Everything You Need To Know About Qi Wireless Charging". Tenpire. June 8, 2019. Retrieved August 20, 2019.
- "Global Qi Standard Powers Up Wireless Charging".
- "Nokia and The Coffee Bean & Tea Leaf® form partnership to introduce wireless charging to cafés across the United States". Nokia. September 5, 2012. Retrieved September 21, 2012.
- "Nokia and Virgin Atlantic partner to introduce wireless charging to Virgin Atlantic Clubhouse Lounges". Nokia. September 5, 2012. Retrieved September 21, 2012.
- "Nokia flies Virgin Atlantic on wireless charging". Nokia. September 11, 2012. Retrieved September 21, 2012.
- "Variable Position Wireless Power Transmitter through Multiple Cooperative Flux Generators".
- Qi – official site