**Parasitic drag** is drag that acts on an object when the object is moving through a fluid. In the case of aerodynamic drag, the fluid is the atmosphere. Parasitic drag is a combination of **form drag** and **skin friction drag**.^{[1]} Parasitic drag does not result from the generation of lift on the object, and hence it is considered parasitic.

The other components of total drag, **lift–induced drag**, **wave drag**, and **ram drag** (see ram pressure), are separate types of drag, and are not components of parasitic drag.

## Description

In flight, lift–induced drag results from the lift force that must be produced so that the craft can maintain level flight. Induced drag is greater at lower speeds where a high angle of attack is required. As speed increases, the induced drag decreases, but parasitic drag increases because the fluid is striking the object with greater force, and is moving across the object's surfaces at higher speed. As speed continues to increase into the transonic and supersonic regimes, wave drag grows in importance. Each of these drag components changes in proportion to the others based on speed. The combined overall drag curve therefore shows a minimum at some airspeed; an aircraft flying at this speed will be close to its optimal efficiency. Pilots will use this speed to maximize the gliding range in case of an engine failure. However, to maximize the gliding endurance (minimum sink), the aircraft's speed would have to be at the point of minimum drag power, which occurs at lower speeds than minimum drag.

At the point of minimum drag, C_{D,o} (drag coefficient of the aircraft when lift equals zero) is equal to C_{D,i} (induced drag coefficient, or coefficient of drag created by lift). At the point of minimum power, C_{D,o} is equal to one third times C_{D,i}. This can be proven by deriving the following equations:^{[clarification needed]}

where:

is the dynamic pressure and

where

- ,
- is the aspect ratio,

## Form drag

**Form drag** or **pressure drag** arises because of the shape of the object. The general size and shape of the body are the most important factors in form drag; bodies with a larger presented cross-section will have a higher drag than thinner bodies; sleek ("streamlined") objects have lower form drag. Form drag follows the drag equation, meaning that it increases with velocity, and thus becomes more important for high-speed aircraft.

Form drag depends on the longitudinal section of the body. A prudent choice of body profile is essential for a low drag coefficient. Streamlines should be continuous, and separation of the boundary layer with its attendant vortices should be avoided.

## Skin friction drag

*Skin friction drag* arises from the friction of the fluid against the "skin" of the object that is moving through it. Skin friction arises from the interaction between the fluid and the skin of the body, and is directly related to the wetted surface, the area of the surface of the body that is in contact with the fluid. Air in contact with a body will stick to the body's surface and that layer will tend to stick to the next layer of air and that in turn to further layers, hence the body is dragging some amount of air with it. The force required to drag an "attached" layer of air with the body is called skin friction drag. Skin friction drag imparts some momentum to a mass of air as it passes through it and that air applies a retarding force on the body. As with other components of parasitic drag, skin friction follows the drag equation and rises with the square of the velocity.

Skin friction is caused by viscous drag in the boundary layer around the object. The boundary layer at the front of the object is usually laminar and relatively thin, but becomes turbulent and thicker towards the rear. The position of the transition point from laminar to turbulent flow depends on the shape of the object. There are two ways to decrease friction drag: the first is to shape the moving body so that laminar flow is possible. The second method is to increase the length and decrease the cross-section of the moving object as much as practicable. To do so, a designer can consider the fineness ratio, which is the length of the aircraft divided by its diameter at the widest point (L/D). It is mostly kept 6:1 for subsonic flows. Increase in length increases Reynolds number. With Reynolds no. in the denominator for skin friction coefficient's relation, as its value is increased (in laminar range), total friction drag is reduced. While decrease in cross-sectional area decreases drag force on the body as the disturbance in air flow is less. For wings of an aircraft, a decrease in length (chord) of the wings will reduce "induced" drag though, if not the friction drag.

The skin friction coefficient, , is defined by

where is the local wall shear stress, and q is the free-stream dynamic pressure.^{[2]}
There are two ways...if not the friction drag.,^{[3]}^{[4]}
For boundary layers without a pressure gradient in the x direction, it is related to the momentum thickness as

For comparison, the turbulent empirical relation known as the *One-seventh Power *Law* (derived by Theodore von Kármán) is:*

where is the Reynolds number.^{[5]}

## Profile drag

Profile drag is a term usually applied to the drag acting on a wing. With a 2-dimensional wing there is no lift-induced drag so the whole of the drag is profile drag. With a 3-dimensional wing the total drag minus the lift-induced drag is the profile drag^{[6]} - it is defined as the sum of **form drag** and **skin friction**.^{[7]}

## See also

## References

**^**Clancy, L.J. (1975).*Aerodynamics*, Sub-section 5.9. Pitman Publishing. ISBN 0 273 01120 0**^**"Skin friction coefficient -- CFD-Wiki, the free CFD reference".*www.cfd-online.com*. Retrieved 22 April 2018.**^**Fluid Mechanics, Frank M.White, 5th edition, Chapter 7 Flow past immersed bodies, Problem no. 7.16**^**"Induced Drag Coefficient".*www.grc.nasa.gov*. Retrieved 22 April 2018.**^**Introduction to Flight, John Anderson Jr., 7th edition**^**Anderson, John D. (1984).*Fundamentals of Aerodynamics*, p.192, 233. McGraw-Hill Book Company ISBN 0-07-001656-9**^**"Profile drag definition and meaning - Collins English Dictionary".*www.collinsdictionary.com*. Retrieved 22 April 2018.