"NFPA 704: Standard System for the Identification of the Hazards of Materials for Emergency Response" is a standard maintained by the U.S.-based National Fire Protection Association. First "tentatively adopted as a guide" in 1960, and revised several times since then, it defines the colloquial "Safety Square" or "Fire Diamond" used by emergency personnel to quickly and easily identify the risks posed by hazardous materials. This helps determine what, if any, special equipment should be used, procedures followed, or precautions taken during the initial stages of an emergency response.
The four divisions are typically color-coded with red on top indicating flammability, blue on the left indicating level of health hazard, yellow on the right for chemical reactivity, and white containing codes for special hazards. Each of health, flammability and reactivity is rated on a scale from 0 (no hazard) to 4 (severe hazard). The latest version of NFPA 704 sections 5, 6, 7 and 8 for the specifications of each classification are listed below. The numeric values in the first column are designated in the standard by "Degree of Hazard" using Arabic numerals (0, 1, 2, 3, 4), not to be confused with other classification systems, such as that in the NFPA 30 Flammable and Combustible Liquids Code, where flammable and combustible liquid categories are designated by "Class", using Roman numerals (I, II, III).
|0||Materials that will not burn under typical fire conditions (e.g. carbon tetrachloride), including intrinsically noncombustible materials such as concrete, stone, and sand. Materials that will not burn in air when exposed to a temperature of 820 °C (1,500 °F) for a period of 5 minutes.|
|1||Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur (e.g. mineral oil, ammonia). Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F).|
|2||Must be moderately heated or exposed to relatively high ambient temperature before ignition can occur (e.g. diesel fuel, paper, sulfur and multiple finely divided suspended solids that do not require heating before ignition can occur). Flash point between 37.8 and 93.3 °C (100 and 200 °F).|
|3||Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions (e.g. gasoline, acetone). Liquids having a flash point below 22.8 °C (73 °F) and having a boiling point at or above 37.8 °C (100 °F) or having a flash point between 22.8 and 37.8 °C (73 and 100 °F).|
|4||Will rapidly or completely vaporize at normal atmospheric pressure and temperature, or is readily dispersed in air and will burn readily (e.g. acetylene, propane, hydrogen gas, diborane). Includes pyrophoric substances. Flash point below room temperature at 22.8 °C (73 °F).|
|0||Poses no health hazard, no precautions necessary and would offer no hazard beyond that of ordinary combustible materials (e.g. wood, paper)|
|1||Exposure would cause irritation with only minor residual injury (e.g. acetone, sodium bromate, potassium chloride)|
|2||Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, carbon dioxide, iodine, chloroform, DEET).|
|3||Short exposure could cause serious temporary or moderate residual injury (e.g. liquid hydrogen, sulfuric acid, calcium hypochlorite, carbon monoxide, hexafluorosilicic acid, zinc chloride)|
|4||Very short exposure could cause death or major residual injury (e.g. hydrogen cyanide, phosgene, diborane, methyl isocyanate, hydrofluoric acid)|
|0||Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium, N2)|
|1||Normally stable, but can become unstable at elevated temperatures and pressures (e.g. propene)|
|2||Undergoes violent chemical change at elevated temperatures and pressures, reacts violently with water, or may form explosive mixtures with water (e.g. white phosphorus, potassium, sodium)|
|3||Capable of detonation or explosive decomposition but requires a strong initiating source, must be heated under confinement before initiation, reacts explosively with water, or will detonate if severely shocked (e.g. ammonium nitrate, caesium, diborane, hydrogen peroxide)|
|4||Readily capable of detonation or explosive decomposition at normal temperatures and pressures (e.g. nitroglycerin, chlorine dioxide, nitrogen triiodide, manganese heptoxide, azidoazide azide, TNT)|
|Special notice (white)|
|The white "special notice" area can contain several symbols. The following symbols are defined by the NFPA 704 standard.|
|OX||Oxidizer, allows chemicals to burn without an air supply (e.g. potassium perchlorate, ammonium nitrate, hydrogen peroxide).|
|Reacts with water in an unusual or dangerous manner (e.g. caesium, sodium, diborane, sulfuric acid).|
|SA||Simple asphyxiant gas (specifically helium, nitrogen, neon, argon, krypton, xenon). The SA symbol shall also be used for liquefied carbon dioxide vapor withdrawal systems and where large quantities of dry ice are used in confined areas.|
|Non-standard symbols (white)|
|These hazard codes are not part of the NFPA 704 standard, but are occasionally used in an unofficial manner. The use of non-standard codes may be permitted, required or disallowed by the authority having jurisdiction (e.g. fire department).|
|COR||Corrosive; strong acid or base (e.g. sulfuric acid, potassium hydroxide)|
|ACID||Acid or alkaline, to be more specific|
|BIO||Biological hazard (e.g. flu virus, rabies virus)|
|POI||Poisonous (e.g. strychnine, alpha-amanitin)|
|RA||Radioactive (e.g. plutonium, cobalt-60, carbon-14)|
|CRY||Cryogenic (e.g. liquid nitrogen)|
- Dr. W. H. L. Dornette, Miles E. Woodworth (1969). "Proposed Amendments on Revisions to the Recommended System for the Identification of The Fire Hazards of Materials / NFPA No. 704M — 1969" (PDF). National Fire Protection Association. Retrieved 2016-03-04.CS1 maint: uses authors parameter (link)
- "NFPA 704: Standard System for the Identification of the Hazards of Materials for Emergency Response". 2017.
|Wikimedia Commons has media related to NFPA 704 images.|
- NFPA Diamond Diagram Guide
- "Frequently Asked Questions on NFPA 704" (PDF).
- "Pamphlet produced by the City of Milwaukee summarizing NFPA 704 code requirements" (PDF). City of Milwaukee.
- "Hazard Communication". Occupational Safety and Health Administration.
- "Safety in the Chemistry Laboratory: NFPA 704 Hazard Identification System". University of Oregon. Archived from the original on 2015-03-10.