Molten-salt batteries are a class of battery that uses molten salts as an electrolyte and offers both a high energy density and a high power density. Traditional non-rechargeable thermal batteries can be stored in their solid state at room temperature for long periods of time before being activated by heating. Rechargeable liquid-metal batteries are used for electric vehicles and potentially also for grid energy storage, to balance out intermittent renewable power sources such as solar panels and wind turbines.
Thermal batteries originated during World War II when German scientist Georg Otto Erb developed the first practical cells using a salt mixture as an electrolyte. Erb developed batteries for military applications, including the V-1 flying bomb and the V-2 rocket, and artillery fuzing systems. None of these batteries entered field use during the war. Afterwards, Erb was interrogated by British intelligence. His work was reported in "The Theory and Practice of Thermal Cells". This information was subsequently passed on to the United States Ordnance Development Division of the National Bureau of Standards. When the technology reached the United States in 1946, it was immediately applied to replacing the troublesome liquid-based systems that had previously been used to power artillery proximity fuzes. They were used for ordnance applications (e.g., proximity fuzes) since WWII and later in nuclear weapons. The same technology was studied by Argonne National Laboratories and other researchers in the 1980s for use in electric vehicles.
Thermal batteries (non-rechargeable)
Thermal batteries use an electrolyte that is solid and inactive at ambient temperatures. They can be stored indefinitely (over 50 years) yet provide full power in an instant when required. Once activated, they provide a burst of high power for a short period (a few tens of seconds to 60 minutes or more), with output ranging from watts to kilowatts. The high power is due to the high ionic conductivity of the molten salt, which is three orders of magnitude (or more) greater than that of the sulfuric acid in a lead–acid car battery.
One design uses a fuze strip (containing barium chromate and powdered zirconium metal in a ceramic paper) along the edge of the heat pellets to initiate burning. The fuze strip is typically fired by an electrical igniter or squib by application of electric current.
Another design uses a central hole in the middle of the battery stack, into which the high-energy electrical igniter fires a mixture of hot gases and incandescent particles. This allows much shorter activation times (tens of milliseconds) vs. hundreds of milliseconds for the edge-strip design. Battery activation can be accomplished by a percussion primer, similar to a shotgun shell. The heat source should be gasless. The standard heat source typically consist of mixtures of iron powder and potassium perchlorate in weight ratios of 88/12, 86/14, or 84/16. The higher the potassium perchlorate level, the higher the heat output (nominally 200, 259, and 297 cal/g respectively). This property of unactivated storage has the double benefit of avoiding deterioration of the active materials during storage and eliminating capacity loss due to self-discharge until the battery is activated.
In the 1980s lithium-alloy anodes replaced calcium or magnesium anodes, with cathodes of calcium chromate, vanadium or tungsten oxides. Lithium–silicon alloys are favored over the earlier lithium–aluminium alloys. The corresponding cathode for use with the lithium-alloy anodes is mainly iron disulfide (pyrite) replaced by cobalt disulfide for high-power applications. The electrolyte is normally a eutectic mixture of lithium chloride and potassium chloride.
More recently, other lower-melting, eutectic electrolytes based on lithium bromide, potassium bromide, and lithium chloride or lithium fluoride have also been used to provide longer operational lifetimes; they are also better conductors. The so-called "all-lithium" electrolyte based on lithium chloride, lithium bromide, and lithium fluoride (no potassium salts) is also used for high-power applications, because of its high ionic conductivity. A radioisotope thermal generator, such as in the form of pellets of 90SrTiO4, can be used for long-term delivery of heat for the battery after activation, keeping it in a molten state.
Thermal batteries are used almost exclusively for military applications, notably for guided missiles. They are the primary power source for many missiles such as the AIM-9 Sidewinder, MIM-104 Patriot, BGM-71 TOW, BGM-109 Tomahawk and others. In these batteries the electrolyte is immobilized when molten by a special grade of magnesium oxide that holds it in place by capillary action. This powdered mixture is pressed into pellets to form a separator between the anode and cathode of each cell in the battery stack. As long as the electrolyte (salt) is solid, the battery is inert and remains inactive. Each cell also contains a pyrotechnic heat source, which is used to heat the cell to the typical operating temperature of 400–550 °C.
Since the mid-1960s much development work has been undertaken on rechargeable batteries using sodium (Na) for the negative electrodes. Sodium is attractive because of its high reduction potential of −2.71 volts, low weight, non-toxic nature, relative abundance, availability and low cost. In order to construct practical batteries, the sodium must be in liquid form. The melting point of sodium is 98 °C (208 °F). This means that sodium-based batteries operate at high temperatures between 400 and 700 °C (750 and 1,300 °F), with newer designs running at temperatures between 245 and 350 °C (470 and 660 °F).
The sodium–sulfur battery (NaS battery), along with the related lithium–sulfur battery employs cheap and abundant electrode materials. It was the first alkali-metal commercial battery. It used liquid sulfur for the positive electrode and a ceramic tube of beta-alumina solid electrolyte (BASE). Insulator corrosion was a problem because they gradually became conductive, and the self-discharge rate increased.
Because of their high specific power, NaS batteries have been proposed for space applications. An NaS battery for space use was successfully tested on the space shuttle mission STS-87 in 1997, but the batteries have not been used operationally in space. NaS batteries have been proposed for use in the high-temperature environment of Venus.
Sodium–nickel chloride (Zebra) battery
A lower-temperature variant of NaS batteries was the development of the ZEBRA (originally, "Zeolite Battery Research Africa"; later, the "Zero Emissions Batteries Research Activity") battery in 1985, originally developed for electric vehicle applications. The battery uses NaAlCl4 with Na+-beta-alumina ceramic electrolyte.
2 battery operates at 245 °C (473 °F) and uses molten sodium tetrachloroaluminate (NaAlCl
4), which has a melting point of 157 °C (315 °F), as the electrolyte. The negative electrode is molten sodium. The positive electrode is nickel in the discharged state and nickel chloride in the charged state. Because nickel and nickel chloride are nearly insoluble in neutral and basic melts, contact is allowed, providing little resistance to charge transfer. Since both NaAlCl
4 and Na are liquid at the operating temperature, a sodium-conducting β-alumina ceramic is used to separate the liquid sodium from the molten NaAlCl
4. The primary elements used in the manufacture of these batteries have much higher worldwide reserves and annual production than lithium.
It was invented in 1985 by the Zeolite Battery Research Africa Project (ZEBRA) group at the Council for Scientific and Industrial Research (CSIR) in Pretoria, South Africa. It can be assembled in the discharged state, using NaCl, Al, nickel and iron powder. The positive electrode is composed mostly of materials in the solid state, which reduces the likelihood of corrosion, improving safety. Its specific energy is 90 Wh/kg; specific power is 150 W/kg. The β-alumina solid ceramic is unreactive to sodium metal and sodium aluminum chloride. Lifetimes of over 1,500 cycles and five years have been demonstrated with full-sized batteries, and over 3,000 cycles and eight years with 10- and 20-cell modules. For comparison, LiFePO4 lithium iron phosphate batteries store 90–110 Wh/kg, and the more common LiCoO2 lithium-ion batteries store 150–200 Wh/kg. A nano lithium-titanate battery stores 72 Wh/kg and can provide power of 760 W/kg.
The ZEBRA's liquid electrolyte freezes at 157 °C (315 °F), and the normal operating temperature range is 270–350 °C (520–660 °F). Adding iron to the cell increases its power response. ZEBRA batteries are currently manufactured by FIAMM Sonick and are used in the Modec Electric Van, the IVECO daily 3.5 ton delivery vehicle,, the prototype Smart ED, and the Th!nk City. In 2011 the US Postal Service began testing all-electric delivery vans, one powered by a ZEBRA battery.
In 2010 General Electric announced a Na-NiCl
2 battery that it called a sodium–metal halide battery, with a 20-year lifetime. Its cathode structure consists of a conductive nickel network, molten salt electrolyte, metal current collector, carbon felt electrolyte reservoir and the active sodium–metal halide salts. In 2015, the company abandoned the project.
Sumitomo developed a battery using a salt that is molten at 61 °C (142 °F), far lower than sodium based batteries, and operational at 90 °C (194 °F). It offers energy densities as high as 290 Wh/L and 224 Wh/kg and charge/discharge rates of 1C with a lifetime of 100 - 1000 charge cycles. The battery employs only nonflammable materials and neither ignites on contact with air nor risks thermal runaway. This eliminates waste-heat storage or fire- and explosion-proof equipment, and allows closer cell packing. The company claimed that the battery required half the volume of lithium-ion batteries and one quarter that of sodium–sulfur batteries. The cell used a nickel cathode and a glassy carbon anode.
In 2014 researchers identified a liquid sodium–cesium alloy that operates at 50 °C (122 °F) and produced 420 milliampere-hours per gram. The new material was able to fully coat, or "wet," the electrolyte. After 100 charge/discharge cycles, a test battery maintained about 97% of its initial storage capacity. The lower operating temperature allowed the use of a less-expensive polymer external casing instead of steel, offsetting some of the increased cost of cesium.
When not in use, Na-NiCl
2 batteries are typically kept molten and ready for use because if allowed to solidify they typically take 12 hours to reheat and charge. This reheating time varies depending on the battery-pack temperature, and power available for reheating. After shutdown a fully charged battery pack loses enough energy to cool and solidify in 3–4 days.
Professor Donald Sadoway at the Massachusetts Institute of Technology has pioneered the research of liquid-metal rechargeable batteries. Both Magnesium–antimony and more recently lead–antimony were used in experiments at MIT. The electrode and electrolyte layers are heated until they are liquid and self-segregate due to density and immiscibility. They may have longer lifetimes than conventional batteries, as the electrodes go through a cycle of creation and destruction during the charge–discharge cycle, which makes them immune to degradation affecting conventional battery electrodes.
The technology was proposed in 2009 based on magnesium and antimony separated by a molten salt. Magnesium was chosen as the negative electrode for its low cost and low solubility in the molten-salt electrolyte. Antimony was selected as the positive electrode due to its low cost and higher anticipated discharge voltage.
In 2011, the researchers demonstrated a cell with a lithium anode and a lead–antimony cathode, which had higher ionic conductivity and lower melting points (350–430 °C). The drawback of the Li chemistry is higher cost. A Li/LiF + LiCl + LiI/Pb-Sb cell with about 0.9 V open-circuit potential operating at 450 °C had electroactive material costs of US$100/kWh and US$100/kW and a projected 25-year lifetime. Its discharge power at 1.1 A/cm2 is only 44% (and 88% at 0.14 A/cm2).
Experimental data shows 69% storage efficiency, with good storage capacity (over 1000 mAh/cm2), low leakage (< 1 mA/cm2) and high maximal discharge capacity (over 200 mA/cm2). By October 2014 the MIT team achieved an operational efficiency of approximately 70% at high charge/discharge rates (275 mA/cm2), similar to that of pumped-storage hydroelectricity and higher efficiencies at lower currents. Tests showed that after 10 years of regular use, the system would retain about 85% of its initial capacity. In September 2014, a study described an arrangement using a molten alloy of lead and antimony for the positive electrode, liquid lithium for the negative electrode; and a molten mixture of lithium salts as the electrolyte.
In 2010, the Liquid Metal Battery Corporation (LMBC) was formed to commercialize the liquid-metal battery technology invented at MIT. LMBC was renamed Ambri in 2012; the name "Ambri" is derived from "cAMBRIdge" Massachusetts, where the company is headquartered and where MIT is located. In 2012 and 2014, Ambri received $40 million in funding from Bill Gates, Khosla Ventures, Total S.A., and GVB.
A recent innovation is the PbBi alloy which enables a very low melting point lithium based battery. It uses a molten salt electrolyte based on LiCl-LiI and operates at 410��°C.
- 9th Intersociety Energy Conversion Engineering Conference Proceedings. American Society of Mechanical Engineers. 1974. p. 665.
- A. E. Martin, in "High Performance Batteries for Electric Vehicles Propulsion and Stationary Energy Storage", Argonne National Laboratories Report ANL-78-94 (1980); and Report ANL-79-39 (1979).
- T.M. O'Sullivan, C.M. Bingham, and R.E. Clark, "Zebra battery technologies for all electric smart car", International Symposium on Power Electronics, Electrical Drives, Automation and Motion, SPEEDAM 2006, IEEE, 23–26 May 2006. Retrieved 12 June 2018
- "Isotope heated deferred action thermal batteries – Catalyst Research Corporation". Freepatentsonline.com. Retrieved 2012-04-24.
- "ASB Group – Military Thermal Batteries". Army Technology. 2011-06-15. Retrieved 2012-04-24.[unreliable source?]
- "EaglePicher – Batteries and Energetic Devices". Naval Technology. 2011-06-15. Retrieved 2012-04-24.[unreliable source?]
- Buchmann, Isidor (August 2011). "Weird and Wonderful Batteries: But Will the Inventions Survive Outside the Laboratory?". Batteries in a Portable World. Retrieved 30 November 2014.
- Koenig, A.A; Rasmussen, J.R (1990). "Development of a high specific power sodium sulfur cell". Proceedings of the 34th International Power Sources Symposium. pp. 30–33. doi:10.1109/IPSS.1990.145783. ISBN 978-0-87942-604-0.
- W. Auxer, "The PB Sodium Sulfur Cell for Satellite Battery Applications", 32nd International Power Sources Symposium, Cherry Hill, NJ, June 9–12, 1986, Proceedings Volume A88-16601, 04-44, Electrochemical Society, Inc., Pennington, NJ, pp. 49–54.
- Landis, Geoffrey A; Harrison, Rachel (2010). "Batteries for Venus Surface Operation". Journal of Propulsion and Power. 26 (4): 649–654. doi:10.2514/1.41886.
- Li, Guosheng; Lu, Xiaochuan; Kim, Jin Y.; Meinhardt, Kerry D.; Chang, Hee Jung; Canfield, Nathan L.; Sprenkle, Vincent L. (11 February 2016). "Advanced intermediate temperature sodium–nickel chloride batteries with ultra-high energy density". Nature Communications. 7: 10683. Bibcode:2016NatCo...710683L. doi:10.1038/ncomms10683. PMC 4753253. PMID 26864635.
- 7.6 The Sodium Nickel Chloride "Zebra" Battery, Meridian International Research, 2006, p. 104-112. Accessed 2 August 2017.
- Sudworth, J.L. (August 1994). "Zebra batteries". Journal of Power Sources. 51 (1–2): 105–114. Bibcode:1994JPS....51..105S. doi:10.1016/0378-7753(94)01967-3.
- Shukla, A. K.; Martha, S. K. (July 2001). "Electrochemical power sources". Resonance. 6 (7): 52–63. doi:10.1007/BF02835270.
- William Tahil, Research Director (December 2006). "The Trouble with Lithium, Implications of Future PHEV Production for Lithium Demand" (PDF). Meridian International Research. Retrieved 2009-02-28.
- Ellis, Brian L.; Nazar, Linda F. (2012). "Sodium and sodium-ion energy storage batteries" (PDF). Current Opinion in Solid State and Materials Science. 16 (4): 168–177. Bibcode:2012COSSM..16..168E. doi:10.1016/j.cossms.2012.04.002.
- Lithium-titanate datasheet.
- Reserve Power Solutions / Technologies / Sodium Nickel Chloride Archived 2013-12-04 at Archive.today
- "Think Global web site". Archived from the original on August 19, 2009.
- Idaho National Labs spec sheet
- "GE Launches Durathon Sodium–Metal Halide Battery for UPS Market". Green Car Congress. 2010-05-18. Retrieved 2012-04-24.
- "GE to Manufacture Molten Salt Sodium Nickel Chloride Batteries for Stationary Electricity Storage Applications".
- "GE Reboots Its Storage Business With a Lithium-Ion Battery and Downstream Services". 2015-04-28.
- "Sumitomo considering marketing new lower-temperature molten-salt electrolyte battery to automakers for EVs and hybrids". Green Car Congress. 2011-11-11. Retrieved 2012-04-24.
- Koji NITTA; Shinji INAZAWA; Shoichiro SAKAI; Atsushi FUKUNAGA; Eiko ITANI; Kouma NUMATA; Rika HAGIWARA & Toshiyuki NOHIRA (April 2013). "Development of Molten Salt Electrolyte Battery" (PDF). SEI TECHNICAL REVIEW.
- Lu, Xiaochuan; Li, Guosheng; Kim, Jin Y.; Mei, Donghai; Lemmon, John P.; Sprenkle, Vincent L.; Liu, Jun (1 August 2014). "Liquid-metal electrode to enable ultra-low temperature sodium–beta alumina batteries for renewable energy storage". Nature Communications. 5 (1): 4578. Bibcode:2014NatCo...5.4578L. doi:10.1038/ncomms5578. PMID 25081362.
- Kim, Hojong; Boysen, Dane A; Newhouse, Jocelyn M; Spatocco, Brian L; Chung, Brice; Burke, Paul J; Bradwell, David J; Jiang, Kai; Tomaszowska, Alina A; Wang, Kangli; Wei, Weifeng; Ortiz, Luis A; Barriga, Salvador A; Poizeau, Sophie M; Sadoway, Donald R (2012). "Liquid Metal Batteries: Past, Present, and Future". Chemical Reviews. 113 (3): 2075–2099. doi:10.1021/cr300205k. PMID 23186356.
- Staff (2012) Ambri Technology Ambri company web page, Retrieved 6 December 2012.
- David L. Chandler, MIT News Office (19 November 2009). "Liquid battery big enough for the electric grid?". MIT News.
- US20110014503 0
- Bradwell, David J; Kim, Hojong; Sirk, Aislinn H. C; Sadoway, Donald R (2012). "Magnesium–Antimony Liquid Metal Battery for Stationary Energy Storage" (PDF). Journal of the American Chemical Society. 134 (4): 1895–1897. CiteSeerX 10.1.1.646.1667. doi:10.1021/ja209759s. PMID 22224420.
- Wang, Kangli; Jiang, Kai; Chung, Brice; Ouchi, Takanari; Burke, Paul J; Boysen, Dane A; Bradwell, David J; Kim, Hojong; Muecke, Ulrich; Sadoway, Donald R (2014). "Lithium–antimony–lead liquid metal battery for grid-level energy storage". Nature. 514 (7522): 348–350. Bibcode:2014Natur.514..348W. doi:10.1038/nature13700. PMID 25252975.
- "Liquid Metal Battery snags funding from Gates firm". CNET. Retrieved 2016-07-27.
- "Ambri Press Release" (PDF). Ambri. August 27, 2012.
- "Liquid Metal Battery Startup from MIT's Don Sadoway Gets $15-Million Boost, Investments from Khosla Ventures, Bill Gates, & Total - CleanTechnica". CleanTechnica.
- "Press Release, "Ambri Raises 35 Million in Series C Round"" (PDF). Ambri.
- Fehrenbacher, Katie (11 September 2015). "Battery startup Ambri lays off staff, pushes back commercial sales". Fortune.
- Eric Wesoff, "Ambri Returns to the Energy Storage Hunt With Liquid Metal Battery Redesign", Green Tech Media, December 14, 2016. Accessed 2 August 2017.
- Kim, Junsoo; Shin, Donghyeok; Jung, Youngjae; Hwang, Soo Min; Song, Taeseup; Kim, Youngsik; Paik, Ungyu (2018). "Li Cl-LiI molten salt electrolyte with bismuth-lead positive electrode for liquid metal battery". Journal of Power Sources. 377: 87–92. Bibcode:2018JPS...377...87K. doi:10.1016/j.jpowsour.2017.11.081.