|Preferred IUPAC name
3D model (JSmol)
CompTox Dashboard (EPA)
|Molar mass||102.177 g·mol−1|
|Odor||Sharp, sweet, ether-like|
|Melting point||−60 °C (−76 °F; 213 K)|
|Boiling point||68.5 °C (155.3 °F; 341.6 K)|
|2 g/L at 20 °C|
|Vapor pressure||119 mmHg (20°C)|
|GHS Signal word||Danger|
|H225, H316, H319, H335, H336, H361, H371, H402, H412|
|P201, P202, P210, P233, P240, P241, P242, P243, P260, P261, P264, P270, P271, P273, P280, P281, P303+361+353, P304+340, P305+351+338, P308+313, P309+311, P312, P332+313, P337+313, P370+378|
|NFPA 704 (fire diamond)|
|Flash point||−28 °C (−18 °F; 245 K)|
|443 °C (829 °F; 716 K)|
|Lethal dose or concentration (LD, LC):|
LD50 (median dose)
|8470 mg/kg (rat, oral)|
LDLo (lowest published)
|5000-6500 mg/kg (rabbit, oral)|
LC50 (median concentration)
|38,138 ppm (rat)|
30,840 ppm (rabbit)
28,486 ppm (rabbit)
|NIOSH (US health exposure limits):|
|TWA 500 ppm (2100 mg/m3)|
|TWA 500 ppm (2100 mg/m3)|
IDLH (Immediate danger)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
|what is ?)(|
Diisopropyl ether is secondary ether that is used as a solvent. It is a colorless liquid that is slightly soluble in water, but miscible with organic solvents. It is used as an extractant and an oxygenate gasoline additive. It is obtained industrially as a byproduct in the production of isopropanol by hydration of propene. Diisopropyl ether is sometimes represented by the abbreviation "DIPE".
Whereas at 20 °C, diethyl ether will dissolve 1% by weight water, DIPE only dissolves half as much. It is used as a specialized solvent to remove or extract polar organic compounds from aqueous solutions, e.g. phenols, ethanol, acetic acid. DIPE is used as an antiknock agent.
Diisopropyl ether can form explosive peroxides upon standing in air for long periods. This reaction proceeds more easily than for ethyl ether, due to the secondary carbon next to the oxygen atom. Antioxidants can be used to prevent this process. The stored solvent should therefore be tested for the presence of peroxides more often (recommended once every 3 months for diisopropyl ether vs. once every 12 months for ethyl ether). Peroxides may be removed by shaking the ether with a solution of iron(II) sulfate. For safety reasons, methyl tert-butyl ether is often used as an alternative solvent.
- NIOSH Pocket Guide to Chemical Hazards. "#0362". National Institute for Occupational Safety and Health (NIOSH).
- "Isopropyl ether". Immediately Dangerous to Life and Health Concentrations (IDLH). National Institute for Occupational Safety and Health (NIOSH).
- Michael Sakuth, Thomas Mensing, Joachim Schuler, Wilhelm Heitmann, Günther Strehlke, Dieter Mayer ³Ethers, Aliphatic² Ullmann's Encyclopedia of Industrial Chemistry 2010, Wiley-VCH, Weinheim. doi:10.1002/14356007.a10_023.pub2