A clipper was a type of mid-19th-century merchant sailing vessel, designed for speed. Clippers were generally narrow for their length, small by later 19th century standards, could carry limited bulk freight, and had a large total sail area. "Clipper" does not refer to a specific sailplan; clippers may be schooners, brigs, brigantines, etc., as well as full-rigged ships. Clippers were mostly constructed in British and American shipyards, though France, Brazil, the Netherlands and other nations also produced some. Clippers sailed all over the world, primarily on the trade routes between the United Kingdom and China, in transatlantic trade, and on the New York-to-San Francisco route around Cape Horn during the California Gold Rush. Dutch clippers were built beginning in the 1850s for the tea trade and passenger service to Java.
The boom years of the clipper era began in 1843 in response to a growing demand for faster delivery of tea from China. This continued under the stimulating influence of the discovery of gold in California and Australia in 1848 and 1851, and ended with the opening of the Suez Canal in 1869.
Origin and usage of "clipper"
The term "clipper" most likely derives from the verb "clip", which in former times meant, among other things, to run or fly swiftly. Dryden, the English poet, used the word "clip" to describe the swift flight of a falcon in the 17th century when he said "And, with her eagerness the quarry missed, Straight flies at check, and clips it down the wind." The ships appeared to clip along the ocean water. The term "clip" became synonymous with "speed" and was also applied to fast horses and sailing ships. "To clip it", and "going at a good clip", remained familiar expressions in the early 20th century.
The first application of the term "clipper", in a nautical sense, is uncertain. The Baltimore Clipper was in use over the last quarter of the 18th century through to the first half of the 19th century, but under a different name for much of that time. At first, these vessels were referred to as "Virginia-built" or "pilot-boat model"—with the name "Baltimore-built" appearing during the War of 1812. It was not until the final days of the slave trade (c. 1835 -1850)—just as the type was dying out—that the name "Baltimore Clipper" became common. The retrospective application of the word "clipper" to this type has been a source of confusion.
The Oxford English Dictionary's earliest quote (referring to the Baltimore Clipper) is from 1824. British newspaper usage of the term can be found as early as 1832 and in shipping adverts from 1835. A US court case of 1834 has evidence which discusses a clipper being faster than a brig.
A clipper is a sailing vessel designed for speed, with that priority taking precedence over cargo carrying capacity, or building or operating costs. It is not restricted to any one rig, and while many were fully rigged ships, others were barques, brigs or schooners. Nor was the term restricted to any one hull type. Howard Chapelle lists three basic hull types for clippers. The first was characterised by the sharp deadrise and ends found in the Baltimore Clipper. The second was a hull with a full mid-section and modest deadrise, but sharp ends - this was a development of the hull-form of transatlantic packets. The third was more experimental, with deadrise and sharpness being balanced against the need to carry a profitable quantity of cargo. As well as a fast hull, a clipper carried a large sail area - by the standards of any other type of sailing ship, a clipper was greatly over-canvassed. The last defining feature of a clipper, in the view of maritime historian David MacGregor, was a captain who had the courage, skill and determination to get the fastest speed possible out of her.:16-21:321-322
In assessing the hull of a clipper, different maritime historians use different criteria to measure "sharpness". "Sharpness" or "fineness" is explained by comparing a rectangular cuboid with the underwater shape of a vessel's hull. The more material you have to carve off the cuboid to achieve the hull shape, the sharper the hull. Ideally a maritime historian would be able to look at either the block coefficient of fineness or the prismatic coefficient[a] of various clippers, but measured drawings or accurate half-models may not exist to calculate either of these figures.(pp43–45) An alternative measure of sharpness for hulls of a broadly similar shape is the coefficient of under-deck-tonnage, as used by David MacGregor in comparing tea clippers. This could be calculated from the measurements taken to determine the registered tonnage, and so can be applied to more vessels.:87-88
An "extreme clipper" has a hull of great sharpness, as judged either by the prismatic coefficient, the coefficient of under-deck-tonnage or some other technical assessment of hull shape. It is a term that has been misapplied in the past, without reference to hull shape. As commercial vessels, these are totally reliant on speed to generate a profit for their owners, as their sharpness limits their cargo carrying capacity.
A "medium clipper" has a cargo-carrying hull that has some sharpness. In the right conditions and with a capable captain, some of these achieved notable quick passages. They were also able to pay their way when the high freight rates often paid to a fast sailer were not available (in a fluctuating market).
The term "clipper" applied to vessels between these two categories. They often made passages as fast as extreme clippers, but had less difficulty in making a living when freight rates were lower.:16
The first ships to which the term "clipper" seems to have been applied were the Baltimore clippers, developed in Chesapeake Bay before the American Revolution, and reaching their zenith between 1795 and 1815. They were small, rarely exceeding 200 tons OM. Their hulls were sharp ended and displayed a lot of deadrise. They were rigged as schooners, brigs or brigantines. In the War of 1812 some were lightly armed, sailing under Letters of Marque and Reprisal, when the type—exemplified by Chasseur, launched at Fells Point, Baltimore in 1814—became known for her incredible speed; the deep draft enabled the Baltimore clipper to sail close to the wind. Clippers, running the British blockade of Baltimore, came to be recognized for speed rather than cargo space.
Speed was also required for the Chinese opium trade between India and China. Small, sharp-bowed British vessels, called opium clippers, were the result.
Meanwhile, Baltimore clippers continued to be built, in particular specifically for the opium trade between India and China, a trade that had become unprofitable for American shipowners by 1849.
Ann McKim, built in Baltimore in 1833 by the Kennard & Williamson shipyard, is considered to be the original clipper ship. She measured 494 tons OM, and was built on the enlarged lines of a Baltimore clipper, with sharply raked stem, counter stern and square rig. Although Ann McKim was the first large clipper ship ever constructed, it cannot be said that she founded the clipper ship era, or even that she directly influenced shipbuilders, since no other ship was built like her; but she may have suggested the clipper design in vessels of ship rig. She did, however, influence the building of Rainbow in 1845, the first extreme clipper ship.
In Aberdeen, Scotland, the shipbuilders Alexander Hall and Sons developed the "Aberdeen" clipper bow in the late 1830s: the first was Scottish Maid launched in 1839. Scottish Maid, 150 tons OM, was the first British clipper ship. "Scottish Maid was intended for the Aberdeen-London trade, where speed was crucial to compete with steamships. The Hall brothers tested various hulls in a water tank and found the clipper design most effective. The design was influenced by tonnage regulations. Tonnage measured a ship's cargo capacity and was used to calculate tax and harbour dues. The new 1836 regulations measured depth and breadth with length measured at half midship depth. Extra length above this level was tax-free and became a feature of clippers. Scottish Maid proved swift and reliable and the design was widely copied." The earliest British clipper ships were built for trade within the British Isles (Scottish Maid was built for the Aberdeen to London trade). Then followed the vast clipper trade of tea, opium, spices and other goods from the Far East to Europe, and the ships became known as "tea clippers".
From 1839, larger American clipper ships started to be built beginning with Akbar, 650 tons OM, in 1839, and including the 1844-built Houqua, 581 tons OM. These larger vessels were built predominantly for use in the China tea trade and known as "tea clippers". Smaller clipper vessels also continued to be built predominantly for the China opium trade and known as "opium clippers" such as the 1842-built Ariel, 100 tons OM.
Then in 1845 Rainbow, 757 tons OM, the first extreme clipper was launched in New York. These American clippers were larger vessels designed to sacrifice cargo capacity for speed. They had a bow lengthened above the water, a drawing out and sharpening of the forward body, and the greatest breadth further aft. Extreme clippers were built in the period 1845 to 1855.
In 1851, shipbuilders in Medford, Massachusetts built the Antelope, often called the Antelope of Boston to distinguish her from other ships of the same name. This vessel is sometimes called one of the first medium clipper ships. A ship-design journalist noted that "the design of her model was to combine large stowage capacity with good sailing qualities." The Antelope was relatively flat-floored and had only an 8-inch dead rise at half-floor.
The medium clipper, though still very fast, could carry more cargo. After 1854 extreme clippers were replaced in American shipbuilding yards by medium clippers.
The Flying Cloud was a clipper ship that claimed the fastest passage between New York and San Francisco, 89 days 8 hours. (The other contender for this "blue ribbon" title was the medium clipper Andrew Jackson—there is an unresolvable argument over timing these voyages "from pilot to pilot").:60-61 Flying Cloud was the most famous of the clippers built by Donald McKay. She was known for her extremely close race with the Hornet in 1853; for having a woman navigator, Eleanor Creesy, wife of Josiah Perkins Creesy, who skippered the Flying Cloud on two record-setting voyages from New York to San Francisco; and for sailing in the Australia and timber trades.
Clipper ships largely ceased being built in American shipyards in 1859 when, unlike the earlier boom years, only four clipper ships were built; a few were built in the 1860s. The last American clipper ship was "the Pilgrim" launched in 1873 from the shipyards of Medford, Massachusetts, built by Joshua T. Foster. Among shipowners of the day, "Medford-built" came to mean the best.
British clipper ships continued to be built after 1859. Earlier British clipper ships had become known as extreme clippers, and were considered to be "as sharp as the American"-built ships. From 1859 a new design was developed for British clipper ships that was nothing like the American clippers; these ships continued to be called extreme clippers. The new design had a sleek graceful appearance, less sheer, less freeboard, lower bulwarks, and smaller breadth. They were built for the China tea trade, starting with Falcon in 1859, and continuing until 1870. It is estimated that 25 to 30 of these ships were built, with no more than four or five in a year. The earlier ships were made from wood, though some were made from iron, just as some British clippers had been made from iron prior to 1859. In 1863 the first tea clippers of composite construction were brought out, combining the best of both worlds. Composite clippers had the strength of iron spars with wooden hulls, and copper sheathing could be added to prevent the fouling that occurred on iron hulls.
After 1869, with the opening of the Suez Canal that greatly advantaged steam vessels (see Decline below), the tea trade collapsed for clippers. From the late 1860s until the early 1870s the clipper trade increasingly focused on the Britain to Australia and New Zealand route, carrying goods and immigrants, services that had begun earlier with the Australian Gold Rush of the 1850s. British-built clipper ships and many American-built British-owned ships were used. Even in the 1880s, sailing ships were still the main carriers of cargoes between Britain, and Australia and New Zealand. This trade eventually became unprofitable, and the ageing clipper fleet became unseaworthy.
China clippers and the apogee of sail
Among the most notable clippers were the China clippers, also called tea clippers or opium clippers, designed to ply the trade routes between Europe and the East Indies. The last example of these still in reasonable condition is Cutty Sark, preserved in dry dock at Greenwich, United Kingdom. Damaged by fire on 21 May 2007 while undergoing conservation, the ship was permanently elevated three metres above the dry dock floor in 2010 as part of a plan for long-term preservation.
Before the early 18th century, the East India Company paid for its tea mainly in silver. When the Chinese Emperor chose to embargo European manufactured commodities and demand payment for all Chinese goods in silver, the price rose, restricting trade. The East India Company began to produce something desired by the Chinese as much as tea was by the British: opium. This had a significant influence on both India and China. Opium was also imported into Britain and was not prohibited because it was thought to be medically beneficial. Laudanum, made from opium, was used as a pain killer, to induce sleep and to suppress anxiety. The famous literary opium addicts Thomas De Quincey, Samuel Taylor Coleridge and Wilkie Collins also took it for its pleasurable effects. The Limehouse area in London was notorious for its opium dens, many of which catered for Chinese sailors as well as English addicts.
Clippers were built for seasonal trades such as tea, where an early cargo was more valuable, or for passenger routes. One passenger ship survives, the City of Adelaide designed by William Pile of Sunderland. The fast ships were ideally suited to low-volume, high-profit goods, such as tea, opium, spices, people, and mail. The return could be spectacular. The Challenger returned from Shanghai with "the most valuable cargo of tea and silk ever to be laden in one bottom". Competition among the clippers was public and fierce, with their times recorded in the newspapers.
The last China clippers were acknowledged as the fastest sail vessels. When fully rigged and riding a tradewind, they had peak average speeds of over 16 knots (30 km/h). The Great Tea Race of 1866 showcased their speed. China clippers are the fastest commercial sailing vessels ever made; their speeds have often been exceeded by modern yachts, but never by a commercial sail vessel. Only the fastest windjammers could attain similar speeds.
There are many ways of judging the speed of a ship: by knots, by day's runs, by port-to-port records. Judged by any test, the American clippers were supreme.
Donald McKay's Sovereign of the Seas reported the highest speed ever achieved by a sailing ship – 22 knots (41 km/h), made while running her easting down to Australia in 1854. (John Griffiths' first clipper, the Rainbow, had a top speed of 14 knots...) There are eleven other instances of a ship's logging 18 knots (33 km/h) or over. Ten of these were recorded by American clippers... Besides the breath-taking 465-nautical-mile (861 km) day's run of the Champion of the Seas, there are thirteen other cases of a ship's sailing over 400 nautical miles (740 km) in 24 hours...
And with few exceptions all the port-to-port sailing records are held by the American clippers.— Lyon, Jane D, p. 138 Clipper Ships and Captains (1962) New York: American Heritage Publishing
The 24h record of the Champion of the Seas wasn't broken until 1984 (by a multihull), or 2001 (by another monohull).
The American clippers sailing from the East Coast to the California goldfields were working in a booming market. Freight rates were high everywhere in the first years of the 1850s. This started to fade in late 1853. The ports of California and Australia reported that they were overstocked with goods that had been shipped earlier in the year. This gave an accelerating fall in freight rates that was halted, however, by the start of the Crimean War in March 1854, as many ships were now being chartered by the French and British governments. The end of the Crimean War in April 1856 released all this capacity back on the world shipping markets - the result being a severe slump. The next year saw the Panic of 1857, which had effects on both sides of the Atlantic. The USA was just starting to recover from this in 1861 when the American Civil War started, causing significant disruption to trade in both Union and Confederate states.:14-15
As the economic situation deteriorated in 1853, American shipowners either did not order new vessels, or specified an ordinary clipper or a medium clipper instead of an extreme clipper. No extreme clipper was launched in an American shipyard after the end of 1854 and only a few medium clippers after 1860.
By contrast, British trade recovered well at the end of the 1850s. Tea clippers had continued to be launched during the depressed years, apparently little affected by the economic downturn.:15 The long-distance route to China was not realistically challenged by steamships in the early part of the 1860s. No true steamer (as opposed to an auxiliary steamship) had the fuel efficiency to carry sufficient cargo to make a profitable voyage. The auxiliary steamships struggled to make any profit.
The situation changed in 1866 when the Alfred Holt-designed and owned SS Agamemnon made her first voyage to China. Holt had persuaded the Board of Trade to allow higher steam pressures in British merchant vessels. Running at 60 psi instead of the previously permitted 25 psi, and using an efficient compound engine, Agamemnon had the fuel efficiency to steam at 10 knots to China and back, with coaling stops at Mauritius on the outward and return legs - crucially carrying sufficient cargo to make a profit.
In 1869 the Suez Canal opened, giving steamships a route about 3,000 NM shorter than that taken by sailing ships round the Cape of Good Hope. Despite initial conservatism by tea merchants, by 1871 tea clippers found strong competition from steamers in the tea ports of China. A typical passage time back to London for a steamer was 58 days, while the very fastest clippers could occasionally make the trip in less than 100 days; the average was 123 days in the 1867–68 tea season.:225–243 The freight rate for a steamer in 1871 was roughly double that paid to a sailing vessel. Some clipper owners were severely caught out by this: several extreme clippers had been launched in 1869, including Cutty Sark, Norman Court and the Caliph.[b]
Of the many clipper ships built during the mid-19th century, only two are known to survive. The only intact survivor is Cutty Sark, which was preserved as a museum ship in 1954 at Greenwich for public display. The other known survivor is City of Adelaide; unlike Cutty Sark she was reduced to a hulk over the years. She eventually sank at her moorings in 1991, but was raised the following year and remained on dry land for years. Adelaide (a.k.a. S.V. Carrick) is the older of the two survivors, and was transported to Australia for conservation.
Clipper ship sailing cards
Departures of clipper ships, mostly from New York and Boston to San Francisco, were advertised by clipper ship sailing cards. These cards, slightly larger than today's postcards, were produced by letterpress and wood engraving on coated card stock. Most clipper cards were printed in the 1850s and 1860s, and represented the first pronounced use of color in American advertising art.
Relatively few (perhaps 3,500) cards survive today. With their rarity and importance as artifacts of nautical, Western, and printing history, clipper cards are highly prized by both private collectors and institutions.
People associated with clipper ships
- List of people who sailed on clipper ships
- Joseph Warren Holmes
- Samuel Hartt Pook
- William Jardine
- Donald McKay
- John (or "Jock") "White Hat" Willis
- The block coefficient of fineness is a mathematical measure of sharpness used by naval architects which compares the hull with a hypothetical block equal in length, breadth and height to the immersed part of the hull. The prismatic coefficient makes a similar comparison to a prism with the immersed hull's dimensions, and is considered to the best indicator of potential speed. The lower the coefficient, the more material has to be removed from the hypothetical cuboid. It is unlikely that many commercial sailing vessels had a prismatic coefficient that was less than 0.57.
- Caution is needed in interpreting Basil Lubbock's count of the number of extreme clippers launched in 1869. He states there were 25, but apparently without evidence such as having sight of reliable plans or half-models. MacGregor stated that at least 5 of those in Lubbock's list were medium clippers, thereby calling into question the categorisation of the others.:253
- Barnwell, R.G. (1857). Commercial Relations of the United States with Foreign Countries. United States Department of State. pp. 260–4.
- Clark, Arthur Hamilton (1912). The Clipper Ship Era: An Epitome of Famous American and British Clipper Ships, Their Owners, Builders, Commanders, and Crews, 1843-1869. G.P. Putnam's Sons.
The Clipper Ship Era.
- Chapelle, Howard Irving (1930). The Baltimore Clipper, its Origin and Development. New York: Bonanza Books.
- "clipper". Oxford English Dictionary (Online ed.). Oxford University Press. (Subscription or participating institution membership required.)
- "Westmeath Journal". 14 June 1832. p. 1.
and may be called an American Clipper
- "Liverpool Standard and General Commercial Advertiser". 22 December 1835. p. 1. Retrieved 13 May 2020.
The well-known Clipper SAGUENAY,
- Gibert, Pedro; United States. Circuit Court (1st Circuit) (1834), A report of the trial of Pedro Gibert, Bernardo de Soto, Francisco Ruiz, Nicola Costa, Antonio Ferrer, Manuel Boyga, Domingo de Guzman, Juan Antonio Portana, Manuel Castillo, Angel Garcia, Jose Velazquez, and Juan Montenegro alias Jose Basilio de Castro, before the United States Circuit Court : on an indictment charging them with the commission of an act of piracy, on board the brig Mexican, of Salem : containing a full statement of the testimony, and the arguments of the counsel on both sides, the charge of the court, pronounced by the Hon. Judge Story : and the verdict of the jury : with an appendix containing several documents never before published, Russell, Odiorne & Metcalf ; Providence : M. Brown & Co. ; Portland : Colman & Chisholm ; Salem : John M. Ives, retrieved 15 September 2019
- MacGregor, David R (1993). British & American Clippers: A Comparison of their Design, Construction and Performance in the 1850s. London: Conway Maritime Press Ltd. ISBN 0-85177-588-8.
- Chapelle, Howard I. (1967). The Search for Speed Under Sail, 1700-1855. Bonanza Books.
- MacGregor, David R. (1983). The Tea Clippers, Their History and Development 1833–1875 (Second ed.). Conway Maritime Press. ISBN 0-85177-256-0.
- Villiers 1973.
- "Fast Sailing Ships: Their Design and Construction, 1775–1875, MacGregor, David R., 1988, Index". Catdir.loc.gov. 18 October 2001. Retrieved 8 April 2013.
- Thomas N. Layton. "The Voyage of the Frolic". Sup.org. Archived from the original on 11 June 2011. Retrieved 8 April 2013.
- Dear, I.C.B., & Kemp, Peter, eds. Oxford Companion to Ships and the Sea (Oxford University Press, 2005).
- Website "Ann McKim" -details, at bruzelius.info Accessed 30 March 2009.
- Ukers, William Harrison (1935). All about Tea. Tea and Coffee Trade Journal Company. pp. 87.
Ann McKim clipper ship.
- "Alexander Hall & Sons Ltd". Aberdeen Ships. 4 November 2006. Retrieved 8 April 2013.
- "Aberdeen Built Ships". Aberdeenships.com. 22 February 2013. Retrieved 8 April 2013.
- "Alexander Hall & Son Shipyard". The Doric Columns - Aberdeen. 1 September 2013. Retrieved 6 June 2020.
- Boston Daily Atlas, 29 November 1851
- Medford Historical Society & Museum:Medford-Built Sailing Ships, at medfordhistorical.org Accessed 19 October 2017
- Jefferson, Sam (4 November 2014). Clipper Ships and the Golden Age of Sail: Races and Rivalries on the Nineteenth Century High Seas. A&C Black. ISBN 9781472900289.
- "The Opium Clippers". Portcities.org.uk. 15 November 2012. Retrieved 8 April 2013.
- Forbes, Allan; Ralph Mason Eastman (1952). Yankee ship sailing cards... State Street Trust Co.
- "24 Hour Distance". Sailspeedrecords.com. Retrieved 8 April 2013.
- Jarvis, Adrian (1993). "Chapter 9: Alfred Holt and the Compound Engine". In Gardiner, Robert; Greenhill, Dr. Basil (eds.). The Advent of Steam - The Merchant Steamship before 1900. Conway Maritime Press Ltd. pp. 158–159. ISBN 0-85177-563-2.
- Clark, Arthur H (1911). The Clipper Ship Era 1843–1869. New York: G. P. Putnam's Sons. p. 332.
- "Agamemnon (1865); Passenger/cargo vessel". Ship models. National Maritime Museum.
- MacGregor, David R. (1988). Fast Sailing Ships, their Design and Construction, 1775-1875 (Second ed.). London: Conway Maritime Press Ltd. ISBN 0-87021-895-6.
- "City of Adelaide website – Condensed History". Cityofadelaide.org.au. Retrieved 8 April 2013.
- Jim Carrick. "The Future of the S.V. Carrick". History Scotland magazine. Archived from the original on 8 February 2006.
- Neale, Jane. "Clipper Ship Cards". American Antiquarian Society. Archived from the original on 8 October 2013. Retrieved 11 July 2014.
- Carl C. Cutler, Greyhounds of the Sea (1930, 3rd ed. Naval Institute Press 1984)
- Alexander Laing, Clipper Ship Men (1944)
- David R. MacGregor, Fast Sailing Ships: Their Design and Construction, 1775–1875 Naval Institute Press, 1988 ISBN 0-87021-895-6
- Oxford English Dictionary (1987) ISBN 0-19-861212-5.
- Bruce D. Roberts, Clipper Ship Sailing Cards, 2007, Lulu.com. ISBN 978-0-9794697-0-1.
- Bruce D. Roberts, Clipper Ship Cards: The High-Water Mark in Early Trade Cards, The Advertising Trade Card Quarterly 1, no. 1 (Spring 1994): 20–22.
- Bruce D. Roberts, Clipper Ship Cards: Graphic Themes and Images, The Advertising Trade Card Quarterly 1, no. 2 (Summer 1994): 22–24.
- Bruce D. Roberts, Museum Collections of Clipper Ship Cards, The Advertising Trade Card Quarterly 2, no. 1 (Spring 1995): 22–24.
- Bruce D. Roberts, Selling Sail with Clipper Ship Cards, Ephemera News 19, no. 2 (Winter 2001): 1, 11–14.
- Chris and Lesley Holden (2009). Life and Death on the Royal Charter. Calgo Publications. ISBN 978-0-9545066-2-9.
Overview and introduction
- Knoblock, Glenn A. (2014). The American Clipper Ship, 1845–1920: A Comprehensive History, with a Listing of Builders and Their Ships. Jefferson: McFarland. ISBN 978-0-7864-7112-6.
- Ross, Donald Gunn III. "Era of the Clipper Ships Web Site". Archived from the original on 30 March 2010. Retrieved 3 September 2011. – Beautifully illustrated introduction, by a member of Donald McKay's family
- Clark, Arthur H. (1910). The Clipper Ship Era, An Epitome of Famous American and British Clipper Ships, Their Owners, Builders, Commanders, and Crews, 1843–1869. Camden, ME: G.P. Putnam’s Sons. – Basic reading, a favorite of Franklin Delano Roosevelt
- Westward by Sea: A Maritime Perspective on American Expansion, 1820–1890, digitized source materials from Mystic Seaport, via Library of Congress American Memory
- Currier & Ives (1959). American clipper ship prints by the Curriers. American Neptune. Salem, MA: The American Neptune.
American clipper ships
- Cutler, Carl C (1984). Greyhounds of the sea: The story of the American clipper ship (3rd ed.). Annapolis, MD: Naval Institute Press. ISBN 978-0-87021-232-1. – The definitive narrative history, useful for checking discrepancies between sources
- Crothers, William L (1997). The American-built clipper ship, 1850–1856 : characteristics, construction, and details. Camden, ME: International Marine. ISBN 0-07-014501-6. – The comprehensive reference for design and construction of American-built clipper ships, with numerous drawings, diagrams, and charts. Gives examples of how each design feature varies in different ships.
- Howe, Octavius T; Matthews, Frederick C. (1986) [First published 1926-1927]. American Clipper Ships 1833–1858. Volume 1 and 2. Salem, MA; New York: Marine Research Society; Dover Publications. ISBN 978-0-486-25115-8. Articles on individual ships, broader coverage than Crothers
Clipper ships by type
- Lubbock, Basil (1984). The China clippers. The Century seafarers. London: Century. ISBN 978-0-7126-0341-6.
- Lubbock, Basil (1968) . The Colonial Clippers (2nd ed.). Glasgow: James Brown & Son. pp. 86–87. OCLC 7831041. – British and Australian clippers
- Lubbock, Basil (1932). The Nitrate Clippers (1st ed.). Glasgow: Brown, Son & Ferguson. pp. 86–87. ISBN 978-0-85174-116-1.
- Lubbock, Basil (1967) . The Opium Clippers. Boston, MA: Charles E. Lauriat Co. ISBN 978-0-85174-241-0. – One of the few comprehensive books on these ships
|Look up clip in Wiktionary, the free dictionary.|
|Wikimedia Commons has media related to Clipper ships.|